Denon RCD-N7 Instruction Manual - Page 9

Connections - rcd n7w

Get Denon RCD-N7 PDF manuals and user guides
UPC - 883795001724
View all Denon RCD-N7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Getting Started Connections Basic Operations Advanced Operations Information Explanation terms Troubleshooting Specifications Index Connections This section explains how to connect speakers, recording equipment, antennas and network. For other connections, see the sections below. NOTE • Do not plug in the power cord until all connections have been completed. • When making connections, also refer to the owner's manual of the other components. • Be sure to connect the left and right channels properly (left with left, right with right). • Do not bundle power supply cords together with connection cables. Doing so can result in humming or noise. Speaker connections Audio cable (sold separately) Pin-plug cable (Black) Speaker cable RCD-N7W WLAN ANTENNA COAX. NETWORK 75ǡ ETHERNET R SPEAKERS L FM AM SUBWOOFER PREOUT AUX OUT AUX IN 1 AUX IN 2 AUX IN 3 (OPTICAL) L LOOP ANT. R SPEAKERS INPEDANCE 4-16 ǡ TUNER ANTENNA ENGLISH Connecting the speaker cables Carefully check the left (L) and right (R) channels and + (red) and - (black) polarities on the speakers being connected to the unit, and be sure to connect the channels and polarities correctly. 1 Peel off about 10 mm of sheathing from the tip of the speaker cable, then either twist the core wire tightly or apply solder to it. 2 Turn the speaker terminal counterclockwise to loosen it. 3 Insert the speaker cable's core wire to all the way into the speaker terminal. 4 Turn the speaker terminal clockwise to tighten it. qw wq Input terminals R L Speaker SC-N7 Subwoofer with built-in amp NOTE Be sure to lower the audio volume before making speaker settings. NOTE • Use speakers with an impedance of 4 to 16 Ω. The protection circuit may be activated if speakers with an impedance other than specified are used. • Connect the speaker cables so they do not stick out of the speaker terminals. The protection circuit may be activated if the wires touch the rear panel or if the + and - sides touch each other (vpage 6 "Protection circuit"). • Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock. • When you connect optional speakers (SC-N7) to this unit, you can perform the filter setting for optimal sound quality output (vpage 35 "Using an optimizing filter"). 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
5
Connections
Connections
Basic Operations
Advanced Operations
Troubleshooting
Explanation terms
Information
Specifications
Index
ENGLISH
Getting Started
This section explains how to connect speakers, recording
equipment, antennas and network.
For other connections, see the sections below.
NOTE
• Do not plug in the power cord until all connections have been
completed.
• When making connections, also refer to the owner’s manual of the
other components.
• Be sure to connect the left and right channels properly (left with left,
right with right).
• Do not bundle power supply cords together with connection cables.
Doing so can result in humming or noise.
Connections
Speaker connections
Audio cable (sold separately)
Pin-plug cable
(Black)
Speaker cable
COAX.
75
ǡ
LOOP
ANT.
L
R
SPEAKERS
ETHERNET
NETWORK
FM
AM
ANTENNA
TUNER
L
R
AUX OUT
AUX IN 1
AUX IN 2
AUX IN 3
(OPTICAL)
WLAN ANTENNA
SPEAKERS INPEDANCE 4-16
ǡ
PREOUT
SUBWOOFER
w
q
w
q
Subwoofer with
built-in amp
Input terminals
R
L
Speaker SC-N7
NOTE
Be sure to lower the audio volume before making speaker settings.
Connecting the speaker cables
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the unit, and be
sure to connect the channels and polarities correctly.
1
Peel off about 10 mm of sheathing
from the tip of the speaker cable, then
either twist the core wire tightly or
apply solder to it.
2
Turn the speaker terminal
counterclockwise to loosen it.
3
Insert the speaker cable’s core wire to
all the way into the speaker terminal.
4
Turn the speaker terminal clockwise
to tighten it.
NOTE
• Use speakers with an impedance of 4 to 16 Ω. The protection circuit
may be activated if speakers with an impedance other than specified
are used.
• Connect the speaker cables so they do not stick out of the speaker
terminals. The protection circuit may be activated if the wires
touch the rear panel or if the + and – sides touch each other
(
v
page 6 “Protection circuit”).
• Never touch the speaker terminals while the power supply is
connected. Doing so could result in electric shock.
• When you connect optional speakers (SC-N7) to this unit, you can
perform the filter setting for optimal sound quality output (
v
page 35
“Using an optimizing filter”).