Denon TU-280 Operating Instructions - Page 7
Denon TU-280 Manual
View all Denon TU-280 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
ENGLISH DESIGNATIONS AND FUNCTIONS OF PANEL CONTROLS (Refer to Page 4.) • POWER ON/STANDBY (Power ON /STANDBY Switch) The unit works 2-3 seconds after this switch is turned on. Whenever the power switch is in the STANDBY state, the apparatus is still connected on AC line voltage. Please be sure to unplug the cord when you leave home for, say, a vacation. 0 PRESET CHANNEL 1-30 (Preset Channel Buttons) These buttons are used for storing broadcast frequencies. When the preset channel buttons are in operation, an indicator 0 goes on. When radio stations are memorized with these buttons, a desired station can be easily tuned by pressing these buttons. 0 SHIFT (Shift Button) This switch is used to select the preset channels from either 1-10 or 11-20 or 21-30. When the shift button is pressed, either 0 or Ej lights up on the SHIFT indicator. Note: After preset tuning, another channel cannot be selected by pressing the shift Button only. Press the preset IDE: Button again to set the signal that you wish to receive. : 1-10 a 11-20 21-30 O TUNING (Tuning Buttons) Used to change the received frequency to a highter frequency (UP) or a lower frequency (DOWN). 0 BAND (Band Button) Selects between FM or AM (MW). 0 AUTO MUTE/MANU (Tuning Mode Button) This switches between auto and manual tuning. Auto tuning: When the UP Button is pressed, the radio is tuned automatically to a higher frequency. Press the DOWN Button to tune to a lower frequency. Use this position to eliminate noise when no signals or weak signals are being received. Manual tuning: In this position, the radio can be tuned manually. Reception is automatically monaural when in the manual mode. 0 MEMORY (Memory Button) This button is used to enable storage of the frequency of a broadcasting station in memory with the Preset channel button 0. When MEMORY is pressed, indicator 0 blinks for approximately 5 seconds. If the PRESET button is pressed during this time interval, the frequency that is currently displayed is stored in memory. Note: If the MEMO indicator 0 is not blinking, pressing the PRESET button will not store the frequency in memory. MEMO (Memory Indicator) This indicator lights when the MEMORY button 0 is pressed. 0 CHANNEL (Channel Indicator) This displays the number of the channel at which the station is stored. DIGITAL FREQUENCY INDICATOR Reception frequencies are indicated numerically. The FM frequency unit is MHz; the AM frequency unit is kHz. SIGNAL (Signal Indicator) This lights when a station can be received. STEREO/MONO (Stereo/Mono Indicator) "STEREO" lights automatically when receiving a stereo broadcast. "MONO" lights when receiving a monaural broadcast or no broadcast at all. TUNING MODE (AUTO/MANUAL) Pressing MODE 0 causes "AUTO" and "MANUAL" to light up alternately. SHIFT ID (Shift Indicator) The preset channel which is selected with the Shift Button 0 is displayed by the SHIFT 0 or O or OE. El : 1 : 11-20 00: 21-30 REMOTE SENSOR (Reniote Control Photosensitive Window) This sensor receives the infrared light transmitted from the wireless remote control unit. When operating the wireless remote control unit, point it towards this sensor. The wireless remote control unit included with the DENON PMA-480R, PMA-680R, PMA-980R etc. can be used to switch the preset channels up or down. OPERATION INSTRUCTIONS PREPARATION CHECKING CONNECTIONS • Check all the connections by referring to connection diagram (Fig. 1). (Refer to Page 5.) • Check that the right (R) and left (L) channels of the speakers are connected to the corresponding right (R) and left (L) plugs, and check that polarities (positive and negative) are correctly matched. • Check that the right (R) and left (L) pins are correctly inserted to the corresponding jacks. • Check that all the cords are firmly connected. * Turn on the power with the POWER switch after checking all the connections. CHECKING ANTENNA 1. Do not incorrectly connect the loop antenna. If you are not sure how to connect the loop antenna, refer to Fig. 1. 2. Use of loop antenna: Keep the loop antenna away from the main body. If the antenna contacts a metal body, reception sensitivity is degraded, thus resulting in unclear reproduction. CAUTION: 1. Whenever the power switch is in the STANDBY position, the unit is still connected on AC line voltage. Please be sure to unplug the cord when you leave home for, say, a vacation. 2. Noise may be generated if a near-by television set is on during AM (MW), FM broadcasting reception. The tuner should be used as far away from a television as possible. 3. When power is supplied again after disconnecting the AC plug on interruption of the power supply, this unit is set automatically to the FM 87.5 MHz, and AUTO MUTE mode.