Dewalt DCD792B Instruction Manual - Page 12
ASSEMBLY AND ADJUSTMENTS, Mode Selector Fig. A, J, Tool Connect™
View all Dewalt DCD792B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
English Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for maximum tightness. To release the accessory, repeat steps 1 and 2 above. ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. Exception-Tool Connect™ functions and mode adjustments require battery to be installed. Mode Selector (Fig. A, J) WARNING: To reduce the risk of injury, remove accessories from the tool chuck before using the mode selector. Your tool is equipped with a mode selector that allows 3 modes to be customized using the Tool Connect™ app. Home settings are active when the home indicator 13 is lit. The following 3 features can be customized. For more information, refer to Table 1 below. Once configured, pressing the mode selector button 12 on the foot of the tool will cycle through the modes 14 . If you are unsure of the current configuration, press the mode selector button 12 to set the tool to the Home setting (home indicator 13 is lit). Fig. J 12 13 14 DeWALT Tool Connect™ WARNING: To reduce the risk of injury, remove accessories from the tool chuck before any Tool Connect™ interaction. NOTICE: Always check the tool configuration prior to use. If you are unsure of the current configuration, press the mode selector button 12 (Fig. J) to set the tool to the Home setting as described on the label and this manual. This tool is capable of connecting with mobile devices that support Bluetooth® Smart (or Bluetooth® 4.0) technology. (To see if your mobile device is compatible, visit: http:// www.bluetooth.com/Pages/Bluetooth-Smart-Devices-List. aspx) DeWALT Tool Connect™ is an application for your smart device (such as a smart phone or tablet) that connects the device to your tool to allow you to configure specific tool functions. Refer to Mode Selector. NOTE: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth®, SIG, Inc. and any use of such marks by DeWALT is under license. Other trademarks and trade names are those of their respective owners. NOTE: The Tool Connect™ App is governed by separate terms and conditions available for viewing through the mobile application. Download the DeWALT Tool Connect™ application at: • Follow the instructions in the app to create your Tool Connect™ account. • On the Home screen of the app, select "+ Tool" to begin the process of adding your tool to the app. • To connect your tool with the DeWALT Tool Connect™ app, at the appropriate screen, press the mode selector button 12 for 3-5 seconds, then wait for the tool to connect. The tool can only be connected to one Tool Connect™ account at a time. • Once the tool has been connected, you can confirm that you would like to register the product. For more information on DeWALT Tool Connect™ functionality and features, please call 1-800-4-DeWALT (1-800-433-9258), visit www.dewalt.com or view the FAQ page and help screens located inside the mobile application. Coin Cell Battery Bluetooth® capability is powered by one coin cell battery in your tool, that when necessary, should be replaced by your local DeWALT service center. Do not attempt to replace the coin cell battery yourself. WARNING: Danger of explosion if battery is incorrectly replaced. WARNING: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD. This product contains a coin/ button cell battery. If the coin/button cell battery is Table 1 Customizable Features Worklight brightness Worklight delay off Maximum speed (RPM) 10 Speed 1 Speed 2 Home MED 20 secs 550 2000 Mode 1 OFF 20 secs 550 2000 Factory Presets Mode 2 MED 20 secs 550 2000 Mode 3 HIGH 20 minutes 550 2000 Customizable Range OFF-HIGH 0-20 minutes 180-550 600-2000