Dewalt DCS356B Instruction Manual - Page 11

Installing/Removing Accessories Fig. B, C

Get Dewalt DCS356B PDF manuals and user guides View all Dewalt DCS356B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installing/Removing Accessories (Fig. B, C) The tool features an exclusive Tool-Free System for faster accessory changes and adjustments without the need for wrenches or hex keys like other oscillating tool systems. 1. Grasp the tool and squeeze the accessory clamping lever 3 . 2. Clean any residual debris from the tool shaft 12 and the accessory clamping lever. 3. Slide the accessory between the shaft and the accessory clamping lever making sure the accessory engages all of the pins 13 on the holder and is flush with the shaft. 4. Release the accessory clamping lever. 5. Some accessories, such as scrapers and blades can be mounted at an angle if required as shown in Figure C. Fig. B English 3. Firmly press the base with the sanding sheet attached against a flat surface and briefly switch the tool on. This provides for good adhesion between the platen and the sanding sheet and also helps to prevent premature wear. NOTE: When the tip of the sanding sheet becomes worn, detach the sheet from the platen, rotate and reapply. Fig. D 13 12 3 Fig. C Attaching Accessories Using the Universal Adapter (Fig. E) CAUTION: To avoid injury, do not use any accessory for an application where the adaptor may fail to hold the accessory. CAUTION: Read and follow all manufacturers' safety  warnings for any accessories used with this tool. CAUTION: To avoid injury, ensure adaptor and accessory are securely tightened. Non-DeWALT accessories can be attached using the universal adaptor. 1. Place the washer 14 on the tool. 2. Place accessory on to washer. 3. Tighten and secure adaptor nut 15 using hex wrench. Fig. E 14 Installing/Removing Sanding Sheets (Fig. D) A diamond shaped platen uses a hook and loop adhesion system to attach the sanding sheets. The platen allows you to use it on large flat surfaces and tight spots or corners. 1. Attach the sanding platen accessory as described under Installing/Removing Accessories. 2. Align the edges on the sanding sheet with the edge of the sanding platen and press the sanding sheet onto the platen. 15 Attaching the Cut Guide (Fig. F) The depth/cut guide allows you to precisely cut material at a specified depth or height and more accurately track a marked cut line. 1. Attach the cut guide block 6 by inserting the tabs 16 on the guide into the accessory side mount 5 on the main body of the tool. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
9
ENGLISH
Fig. E
14
15
Attaching Accessories Using the Universal
Adapter (Fig. E)
±
CAUTION:
To avoid injury, do not use any accessory
for an application where the adaptor may fail to hold
the accessory.
±
CAUTION:
Read and follow all manufacturers’ safety
warnings for any accessories used with this tool.
±
CAUTION:
To avoid injury, ensure adaptor and
accessory are securely tightened.
Non-
D
E
WALT
accessories can be attached using the
universal adaptor.
1. Place the washer
14
on the tool.
2. Place accessory on to washer.
3. Tighten and secure adaptor nut
15
using hex wrench.
Fig. D
Fig. C
Fig. B
3
13
12
Installing/Removing Accessories (Fig. B, C)
The tool features an exclusive Tool-Free System for faster
accessory changes and adjustments without the need for
wrenches or hex keys like other oscillating tool systems.
1. Grasp the tool and squeeze the accessory clamping
lever
3
.
2. Clean any residual debris from the tool shaft
12
and the
accessory clamping lever.
3. Slide the accessory between the shaft and the accessory
clamping lever making sure the accessory engages all of
the pins
13
on the holder and is flush with the shaft.
4. Release the accessory clamping lever.
5. Some accessories, such as scrapers and blades can be
mounted at an angle if required as shown in Figure C.
3. Firmly press the base with the sanding sheet attached
against a flat surface and briefly switch the tool on.
This provides for good adhesion between the platen
and the sanding sheet and also helps to prevent
premature wear.
NOTE:
When the tip of the sanding sheet becomes worn,
detach the sheet from the platen, rotate and reapply.
Installing/Removing Sanding Sheets
(Fig. D)
A diamond shaped platen uses a hook and loop adhesion
system to attach the sanding sheets. The platen allows you
to use it on large flat surfaces and tight spots or corners.
1. Attach the sanding platen accessory as described under
Installing/Removing Accessories
.
2. Align the edges on the sanding sheet with the edge of
the sanding platen and press the sanding sheet onto
the platen.
Attaching the Cut Guide (Fig. F)
The depth/cut guide allows you to precisely cut material
at a specified depth or height and more accurately track a
marked cut line.
1. Attach the cut guide block
6
by inserting the tabs
16 
on the guide into the accessory side mount
5
on the
main body of the tool.