Dewalt DWE46202 Instruction Manual 1 - Page 8
Features, ASSEMBLY AND ADJUSTMENTS, Accessories, Attaching Side Handle Fig. A, Guards, Mounting
View all Dewalt DWE46202 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
English of masonry materials at various work sites (i.e., construction sites). DO NOT use under wet conditions or in presence of flammable liquids or gases. Your heavy-duty small angle grinders is a professional power tool. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. Features DWE46202 E-switch Protection™ The ON/OFF switch has a no-volt release function. In the event of a power outage or other unexpected shut down, the switch will need to be cycled (turned off and then on) to restart tool. E-Clutch™ This unit is equipped with an E-Clutch™ (Electronic Clutch), which in the event of a high-load or wheel pinch, the unit will be shut off to reduce the reaction torque to the user. The switch needs to be cycled (turned off and then on) to restart tool. Brake When the switch is released the motor immediately turns off and electronically brakes stopping the accessory quickly. Kickback Brake™ When a severe pinch, stall, or bind-up event is sensed the electronic brake engages with maximum force to quickly stop the wheel, reduce the movement of the grinder, and shut the grinder off. The switch needs to be cycled (turned off and then on) to restart tool. Constant Clutch™ When overloaded or stalled the motor torque is reduced. If load is reduced the torque and RPM will increase. If the tool is stalled for an extended amount of time it will shut-off and require the switch to cycle to restart. Variable Speed Dial (Fig. A) WARNING: Regardless of the speed setting, the rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. The variable speed dial offers added tool control and enables the tool to be used at optimum conditions to suit the accessory and material. • Turn the dial 7 to the desired level. Turn the dial to the right for higher speed and to the left for lower speed. LED Indicator (Fig. A) The LED indicator 8 will remain lit green during normal activity, or blink in a pattern of red light to alert you a tool protection feature has been activated. Refer to the LED Guide at the back of this manual for explanations of blink patterns. ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect it from power source before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. Accessories The capacity for this shroud is 6" (150mm) diameter x 1/4" (6.35mm) diamond coated steel wheel (diamond wheel). It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See page 10 for information on choosing the correct accessories. WARNING: Handle and store all abrasive wheels carefully to prevent damage from thermal shock, heat, mechanical damage, etc. Store in a dry protected area free from high humidity, freezing temperatures or extreme temperature changes. Attaching Side Handle (Fig. A) WARNING: Before using the tool, check that the handle is tightened securely. Screw the side handle 5 tightly into one of the holes on either side of the gear case. The side handle should always be used to maintain control of the tool at all times. Guards CAUTION: Guards must be used with all grinding wheels, cutting wheels, sanding flap discs, wire brushes, and wire wheels. Refer to Figure A to see guards provided with the unit. Some applications may require purchasing the correct guard and other components from your local dealer or authorized service center. NOTE: The tuckpointing shroud is only to be used in tuckpointing and cutting masonry materials with diamond wheels. NOTE: See the Accessories Chart to select the proper guard / accessory combination. Mounting and Removing Tuckpoint Shroud (Fig. B) 1. Loosen the collar screw 11 on the tuckpoint shroud and align the tabs 21 on the tuckpoint shroud with the slots 22 on the grinder gear case. Fig. B 21 11 22 6