Dewalt DWX725B Instruction Manual - Page 5

Working With Pipes Fig. 5, Carry Strap, Wall Mount Storage, Locking Locator Clip Fig. 6, Carry

Get Dewalt DWX725B PDF manuals and user guides View all Dewalt DWX725B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

English TO MOUNT THE WOOD PIECE 1. Cut a standard 2 x 4 (H) to 35.75" (910 mm) long. 2. Align the 2 x 4 in the top channel of the beam (A). 3. Secure the 2 x 4 to the beam with 2" (50.8 mm) long wood screws inserted from below through the holes in the main beam. NOTE: When the wood surface is attached, a miter saw mounting bracket can not be attached to the stand. Working With Pipes (Fig. 5) If cutting or otherwise working with pipe, the stand has a V notch (I) on each side of the stand to help keep the pipe from rolling when cutting. FIG. 5 I Carry Strap If you purchase the carry strap accessory for DEWALT stands, use the small square hole in the metal end to mount the accessory. Wall Mount Storage If you would like to store your stand out of the way you can mount your stand on the wall. Install a wood screw into a stud, leave a portion protruding from the wall. Use the V notch on the bottom of the metal end to hang the stand vertically on the screw. Locking Locator Clip (Fig. 6) The locking locator clip (J) keeps the optional DW7231 accessory from sliding left or right during cutting operations. It is fixed on the DWX725. FIG. 6 J Carry Handle (Fig. 7) A handle has been supplied to transport the work stand to and from the work site. WARNING: To reduce the risk of personal injury, DO NOT attempt to store or carry the work stand with a tool attached. Loss of control may result. FIG. 7 Clamping Work Material (Fig. 8) The work stand is compatible with the DWS5026 track saw clamp. Insert the clamp's base into the large rectangular hole (K) in the stand end bracket and clamp down on your work material. FIG. 8 K Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, do not create unstable conditions and use only with DEWALT tools. COMPATIBLE PRODUCTS DW7231 - Miter saw mounting brackets DW7026 - Carry strap DWS5026 - TrackSaw™ clamp Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www. dewalt.com. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
3
English
TO MOUNT THE WOOD PIECE
1. Cut a standard 2 x 4 (H) to 35.75" (910 mm) long.
2. Align the 2 x 4 in the top channel of the beam (A).
3. Secure the 2 x 4 to the beam with 2" (50.8 mm) long wood
screws inserted from below through the holes in the main
beam.
NOTE:
When the wood surface is attached, a miter saw mounting
bracket can not be attached to the stand.
Working With Pipes (Fig. 5)
If cutting or otherwise working with pipe, the
FIG. 5
I
stand has a V notch (I) on each side of the
stand to help keep the pipe from rolling
when cutting.
Carry Strap
If you purchase the carry strap accessory for
D
E
WALT stands, use the small square hole
in the metal end to mount the accessory.
Wall Mount Storage
If you would like to store your stand out of the way you can mount
your stand on the wall. Install a wood screw into a stud, leave a
portion protruding from the wall. Use the V notch on the bottom of
the metal end to hang the stand vertically on the screw.
Locking Locator Clip (Fig. 6)
The locking locator clip (J) keeps the optional
J
FIG. 6
DW7231 accessory from sliding left or right
during cutting operations. It is fixed on the
DWX725.
Carry Handle (Fig. 7)
A handle has been supplied to transport the
FIG. 7
work stand to and from the work site.
WARNING:
To reduce the risk of personal
injury,
DO NOT
attempt to store or carry
the work stand with a tool attached. Loss of
control may result.
Clamping Work Material
(Fig. 8)
The work stand is compatible with the DWS5026
K
FIG. 8
track saw clamp. Insert the clamp's base into
the large rectangular hole (K) in the stand end
bracket and clamp down on your work material.
Accessories
WARNING:
Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk of
injury, do not create unstable conditions and use only with D
E
WALT
tools.
COMPATIBLE PRODUCTS
DW7231 – Miter saw mounting brackets
DW7026 – Carry strap
DWS5026 – TrackSaw™ clamp
Recommended accessories for use with your tool are available at
extra cost from your local dealer or authorized service center. If you
need assistance in locating any accessory, please contact D
E
WALT
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,
call 1-800-4-D
E
WALT (1-800-433-9258) or visit our website www.
dewalt.com.