Dewalt DXCMLA4708065 Instruction Manual - Page 21

Inspect Air Lines and Fittings for Leaks

Get Dewalt DXCMLA4708065 PDF manuals and user guides View all Dewalt DXCMLA4708065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

English of the motor drive pulley and equalize B1 and B2, using care not to disturb the belt alignment performed in step 2. 8. Retightenthemotordrivepulleysetscrew.Torqueto145-165inlbs (16.4-20.3 Nm). 9. Reinstall belt guard. Air Compressor Pump Intake and Exhaust Valves Once a year have a Trained Service Technician check the air compressor pump intake and exhaust valves. Inspect Air Lines and Fittings for Leaks 1. Set the Auto/Off lever to "Off", shut off the main power disconnect, and relieve all air pressure from the air tank. 2. Apply a soap solution to all air line fittings and connections/ piping. 3. Correct any leaks found. IMPORTANT: Even minor leaks can cause the air compressor to overwork, resulting in premature breakdown or inadequate performance. Air compressor Head Bolts - Torquing The air compressor pump head bolts should be kept properly torqued. Check the torques of the head bolts after the first five hours of operation. Torque to 14-16 ft.‑lbs. (18.9-21.7 Nm). Service and Adjustments ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN. WARNING: Risk of unsafe operation. Unit cycles automatically when power is on. When servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor to cool. To Replace or Clean Check Valve 1. Release all air pressure from air tank. See Draining Air Tank in the Maintenance section. 2. Set the Auto/Off lever to "Off", shut off the main power disconnect, and relieve all air pressure from the air tank. 3. Using an adjustable wrench loosen outlet tube nut at air tank and pump. Carefully move outlet tube Screwdriver away from check In open valve. position 4. Using an adjustable nothing is visible. wrench loosen pres- sure relief tube nut at air tank. Carefully In closed position disc is visible. move pressure relief tube away from check valve. 5. Unscrew the check valve (turn counterclockwise) using a 7/8" open end wrench. NOTE the orientation for reassembly. 6. Using a screwdriver, carefully push the valve disc up and down. NOTE: The valve disc should move freely up and down on a spring which holds the valve disc in the closed position, if not the check valve needs to be cleaned or replaced. 7. Clean or replace the check valve. A solvent, such as paint or varnish remover can be used to clean the check valve. 8. Apply sealant to the check valve threads. Reinstall the check valve (turn clockwise). 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
21
English
of the motor drive pulley and equalize B1 and B2, using care
not to disturb the belt alignment performed in step 2.
8.
Retighten the motor drive pulley setscrew. Torque to 145–165 in lbs
(16.4–20.3 Nm).
9.
Reinstall belt guard.
Air Compressor Pump Intake and
Exhaust Valves
Once a year have a Trained Service Technician check the air com-
pressor pump intake and exhaust valves.
Inspect Air Lines and Fittings for Leaks
1.
Set the Auto/Off lever to “Off”, shut off the main power discon-
nect, and relieve all air pressure from the air tank.
2.
Apply a soap solution to all air line fittings and connections/
piping.
3.
Correct any leaks found.
I
MPORTANT:
Even minor leaks can cause the air compressor
to overwork, resulting in premature breakdown or inadequate
performance.
Air compressor Head Bolts - Torquing
The air compressor pump head bolts should be kept properly
torqued. Check the torques of the head bolts after the first five
hours of operation. Torque to 14-16 ft.-lbs. (18.9–21.7 Nm).
Service and Adjustments
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED
MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.
WARNING:
Risk of unsafe operation. Unit cycles automati-
cally when power is on. When servicing, you may be exposed
to voltage sources, compressed air, or moving parts. Before
servicing unit unplug or disconnect electrical supply to the air
compressor, bleed tank of pressure, and allow the air compres-
sor to cool.
To Replace or Clean Check Valve
1.
Release all air pressure from air tank. See
Draining Air Tank
in
the
Maintenance
section.
2.
Set the Auto/Off lever to “Off”, shut off the main power discon-
nect, and relieve all air pressure from the air tank.
3.
Using an adjustable
In closed position
disc is visible.
In open
position
nothing is
visible.
Screwdriver
wrench loosen outlet
tube nut at air tank
and pump. Carefully
move
outlet
tube
away
from
check
valve.
4.
Using an adjustable
wrench loosen pres-
sure relief tube nut
at air tank. Carefully
move pressure relief tube away from check valve.
5.
Unscrew the check valve (turn counterclockwise) using a 7/8”
open end wrench.
NOTE
the orientation for reassembly.
6.
Using a screwdriver, carefully push the valve disc up and
down.
NOTE:
The valve disc should move freely up and down
on a spring which holds the valve disc in the closed position, if
not the check valve needs to be cleaned or replaced.
7.
Clean or replace the check valve. A solvent, such as paint or
varnish remover can be used to clean the check valve.
8.
Apply sealant to the check valve threads. Reinstall the check
valve (turn clockwise).