Dirt Devil ND40015 Revision 3 (8/2011) - Page 24

CARRETE DE ALMACENAMIENTO PARA LA MANGUERA DE ALTA PRESIÓN* La manguera de alta presión* se guarda en el carrete indicado cuando la hidrolavadora a presión no está en uso. *Sólo en determinados modelos. Interruptor para ENCENDER/apagar Con este interruptor se enciende y se apaga la hidrolavadora a presión. Empuñadura de la pistola La empuñadura de la pistola tiene una superficie antideslizante que permite tener un mayor control de la lanza de pulverización y sirve para reducir la fatiga. Pistola con seguro Al activar la pistola sale un chorro de agua para limpiar a presión. El seguro sirve para evitar que se use sin autorización. ASSEMBLY UNPACKING This product requires assembly. • Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. WARNING: Do not use this product if any parts on the Packing List are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury. • Inspect the product carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satis factorily operated the product. • If any parts are damaged or missing, please call 1-800-321-1134 for assistance. PACKING LIST Pressure Washer High Pressure Hose High Pressure Hose* (for Hose Reel*) (*In select models only) Trigger Handle Variable Fan Spray Wand Turbo Spray Wand* (*In select models only) Removable Detergent Tank Detergent Tank Holder Spray Wand Holder Garden Hose Coupler Rotary Tool* (*In select models only) Nozzle Cleaning Tool Operator's Manual WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury. WARNING: Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. 24 ASSEMBLY CONTINUED WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury. NOTE: All water inlets are covered by a plastic cap that must be removed before installing hoses onto the pressure washer. INSTALLING THE DETERGENT TANK AND HOLDER Position the groove on the detergent tank holder over the rib on the side of the pressure washer. Push down on the holder until it locks into place. To install the detergent tank, place the tank in the holder and place the cap and tube onto the tank. Push the cap over the neck of the tank and make certain it is installed securely. installing THE spray wand HOLDER See Figure 5. Position the groove on the spray wand holder over the rib on the side of the pressure washer. Push down on the holder until it locks into place. installing/REMOVING accessories* See Figure 6. There may be up to 4 spray wands or brushes included with the pressure washer. The variable fan spray wand produces a flat spray and has a low-to-high pressure adjustment. The turbo spray* wand produces a pencil jet spray for higher intensity cleaning. The rotary tool has a water-generated rotary brush, that can be used for a variety of uses. For higher intensity cleaning use the wedge brush*. (*In select models only) To install spray wand: • Push the end of the spray wand into the trigger handle and rotate clockwise to secure. • Pull on the spray wand to be certain it is properly secured. To remove spray wand: • Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure. • Push in on the spray wand and rotate counter clockwise to remove. connecting high pressure hose to TRIGGER HANDLE See Figure 7. • Place the hex nut over the hose inlet on the trigger handle. • Using a wrench, securely tighten the hex nut. • Pull on the hose to be certain it is properly secured. connecting high pressure extension hose to HOSE REEL* (*In select models) • Place the L-shaped coupler end of the extension hose over the water outlet on the front of the pressure washer. • Securely tighten the collar. • Place the other end of the extension hose over the water inlet on the hose reel. • Securely tighten the collar. • Pull on each hose connection to be certain it is properly secured. connecting the garden hose See Figure 9. Caution: Always observe all local regulations when connecting hoses to the water main. Some areas have restrictions against connecting directly to public drinking water supply to prevent the feedback of chemicals into the drinking water supply. Direct connection through a receiver tank or backflow preventer is usually permitted. 25