E-Z-GO Express S4 - Gas Owner Manual - Page 60

Light Bulb Replacement, Fuse Replacement, Vehicle With A Discharged Battery

Page 60 highlights

MAINTENANCE Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers. LIGHT BULB REPLACEMENT To reduce the possibility of premature bulb failure, do not touch new bulbs with bare fingers. Use clean, dry tissue or paper towel to handle the glass portion of the bulb. For vehicles equipped with lights mounted in the cowl, locate bulb socket on backside of light and turn bulb socket a quarter turn counterclockwise to unlock and pull out bulb and socket. Insert new bulb and rotate socket a quarter turn clockwise to secure. 5 Similarly replace the turn signal light bulb, locate bulb socket on backside of light bar and turn bulb socket a quarter turn counterclockwise to unlock and pull out bulb and socket. Insert new bulb and rotate socket a quarter turn clockwise to secure. Two tail light types were used depending upon the vehicle model; select the type that is installed in the vehicle and follow the instructions for replacing the tail light bulb. Inside of Cowl Headlight Casing Screw Headlight Bulb Roll Rubber Bezel Away From Body Tail/Brake Light Rear Fender Rear Fender Tail Light Lens Tail Light Bulb To replace the tail and brake light bulb, roll the rubber bezel from around the edge of the taillight and remove lens. Install replacement bulb and replace lens. To replace the tail and brake light bulb, remove hardware securing lens and remove lens. Install replacement bulb. FUSE REPLACEMENT To replace fuses, locate the fuse block under the driver side seat. Pull out old fuse and replace with a new automotive type fuse. Headlight and taillight bulbs and fuses are available from a local Distributor, an authorized Branch or the Service Parts Department. VEHICLE WITH A DISCHARGED BATTERY To reduce the possibility of severe injury or death from inadvertent motion, do not attempt to 'jump start' a vehicle. The vehicle is equipped with a starter/generator and does not idle. When starting the engine, the starter/generator functions as a starter and with the engine running, it functions as a generator. With the short running times associated with this kind of vehicle, the generator is more than adequate to maintain the battery charge level. The generator is not designed to charge a discharged battery. 5 - 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86

MAINTENANCE
Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.
5 -
10
5
LIGHT BULB REPLACEMENT
To reduce the possibility of premature bulb failure, do not touch new bulbs with bare fingers. Use clean, dry tissue or
paper towel to handle the glass portion of the bulb.
For vehicles equipped with lights mounted in the cowl,
locate bulb socket on backside of light and turn bulb
socket a quarter turn counterclockwise to unlock and pull
out bulb and socket. Insert new bulb and rotate socket a
quarter turn clockwise to secure.
Similarly replace the turn signal light bulb, locate bulb
socket on backside of light bar and turn bulb socket a
quarter turn counterclockwise to unlock and pull out bulb
and socket. Insert new bulb and rotate socket a quarter
turn clockwise to secure.
Two tail light types were used depending upon the vehi-
cle model; select the type that is installed in the vehicle
and follow the instructions for replacing the tail light
bulb.
To replace the tail and brake light bulb, roll the rubber bezel from around the edge of the taillight and remove lens.
Install replacement bulb and replace lens. To replace the tail and brake light bulb, remove hardware securing lens
and remove lens. Install replacement bulb.
FUSE REPLACEMENT
To replace fuses, locate the fuse block under the driver side seat. Pull out old fuse and replace with a new automo-
tive type fuse. Headlight and taillight bulbs and fuses are available from a local Distributor, an authorized Branch or
the Service Parts Department.
VEHICLE WITH A DISCHARGED BATTERY
To reduce the possibility of severe injury or death from inadvertent motion, do not attempt to
‘jump start’ a vehicle.
The vehicle is equipped with a starter/generator and does not idle. When starting the engine, the starter/generator
functions as a starter and with the engine running, it functions as a generator.
With the short running times associated with this kind of vehicle, the generator is more than adequate to maintain the
battery charge level. The generator is not designed to charge a discharged battery.
Inside of Cowl
Headlight
Casing
Screw
Headlight
Bulb
Rear
Fender
Tail Light
Lens
Tail Light
Bulb
R
ear
F
ender
T
ai
l/
Bra
k
e
L
ight
R
o
ll R
ubber
Be
z
e
l A
wa
y
F
ro
m
Bod
y