Edimax BR-6428HPn Manual - Page 46

Universal Repeater

Get Edimax BR-6428HPn PDF manuals and user guides View all Edimax BR-6428HPn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

network clients to connect to this router. 2.4GHz (G): Allows 802.11g wireless network clients to connect to this router. ESSID Channel Number Associated Clients 2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). This is the name of your router. You can type any alphanumerical character here (maximum 32 characters). Select a channel from the dropdown menu. All access points must use the same channel (1 to 13). Click "Show Active Clients" for the list of all connected wireless clients. Click "Refresh" in the new window to renew the list, and click "Close" to close the window. MAC address 1 to 4 Wireless Module Note: If you have a pop‐up blocker installed, you may have to disable it, or set it to allow the pop‐up window to show up. Input the MAC addresses of the wireless access points with which you wish to connect. Select "Enable" to turn on the 2.4GHz wireless signal and select "Disable" to turn it off. Click "Apply" to save the changes, or click "Cancel" to discard the changes. After you have clicked "Apply", you will see the following message: Click "Apply" to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click "Continue" to configure other settings. 3‐4‐1‐6 Universal Repeater In "Universal Repeater" mode, this broadband router acts as a wireless signal repeater to extend the wireless coverage of the specified wireless access point. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
45
network clients to connect to this router.
2.4GHz (G): Allows 802.11g wireless network clients
to connect to this router.
2.4GHz (B+G+N): Allows 802.11b, 802.11g, and
802.11n wireless clients to connect to this router
(recommended).
ESSID
This is the name of your router. You can type any
alphanumerical character here (maximum 32
characters).
Channel Number
Select a channel from the dropdown menu. All access
points must use the same channel (1 to 13).
Associated Clients
Click “Show Active Clients” for the list of all
connected wireless clients. Click “Refresh” in the
new window to renew the list, and click “Close” to
close the window.
Note: If you have a pop
‐
up blocker installed, you
may have to disable it, or set it to allow the pop
‐
up
window to show up.
MAC address 1 to 4
Input the MAC addresses of the wireless access points
with which you wish to connect.
Wireless Module
Select “Enable” to turn on the 2.4GHz wireless
signal and select “Disable” to turn it off.
Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have
clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60
seconds for the broadband router to restart. Click “Continue” to configure other settings.
3
‐
4
‐
1
‐
6 Universal Repeater
In “Universal Repeater” mode, this broadband router acts as a wireless signal repeater to
extend the wireless coverage of the specified wireless access point.