Edimax BR-6428HPn Manual - Page 48

Security Settings, Disabled

Get Edimax BR-6428HPn PDF manuals and user guides View all Edimax BR-6428HPn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

close the window. Root AP SSID Site Survey Wireless Module Note: If you have a pop‐up blocker installed, you may have to disable it, or set it to allow the pop‐up window to show up. Input the SSID of the wireless access point with which you wish to connect. Click "Select Site Survey" and a pop‐up window will appear. All reachable wireless access points will be shown in the window. Select a wireless access point from the list, and click "Done" to establish a connection. Clicking "Refresh" will renew the list. Select "Enable" to turn on the 2.4GHz wireless signal and select "Disable" to turn it off. Click "Apply" to save the changes, or click "Cancel" to discard the changes. After you have clicked "Apply", you will see the following message: Click "Apply" to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click "Continue" to configure other settings. 3‐4‐2 Security Settings Advanced security settings are available in certain modes to enhance connection security. 3‐4‐2‐1 Disabled Connection encryption is disabled under this mode (not recommended). 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
47
close the window.
Note: If you have a pop
‐
up blocker installed, you
may have to disable it, or set it to allow the pop
‐
up
window to show up.
Root AP SSID
Input the SSID of the wireless access point with
which you wish to connect.
Site Survey
Click “Select Site Survey” and a pop
‐
up window will
appear. All reachable wireless access points will be
shown in the window. Select a wireless access point
from the list, and click “Done” to establish a
connection. Clicking “Refresh” will renew the list.
Wireless Module
Select “Enable” to turn on the 2.4GHz wireless
signal and select “Disable” to turn it off.
Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have
clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60
seconds for the broadband router to restart. Click “Continue” to configure other settings.
3
‐
4
‐
2 Security Settings
Advanced security settings are available in certain modes to enhance connection security.
3
‐
4
‐
2
‐
1 Disabled
Connection encryption is disabled under this mode (not recommended).