Electrolux E30IC80ISS Owners Guide - Page 14

Setting Surface Controls

Get Electrolux E30IC80ISS PDF manuals and user guides View all Electrolux E30IC80ISS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

14 Setting Surface Controls Using the touch control The recommended way to use the touch pads on the cooktop is with your finger placed in the center of the touch pad. If the finger is not placed on the center of a pad, the cooktop may not respond to the selection made. Lightly contact the pad with the flat part of your entire fingertip. Do not just use the narrow end of your fingertip. Operating the cooking zones The Induction cooktop has four or five Cooking Zones designed for cookware of various sizes. Be sure to place cookware that meets the minimum and maximum pan size requirements (see Fig. 2, page 11) for the Cooking Zone desired and is best for the amount of food being prepared. Place the cookware with the prepared food on the Cooking Zone BEFORE setting any of the Cooktop controls. To Turn ON one or more of the Cooking Zones: 1. Place the prepared food using the correct type and size cookware on the desired Cooking Zone. Be sure to center the cookware on Cooking Zone completely covering the minimum ring marked on the Zone surface. PLEASE NOTE: If the cookware requirements for the Cooking Zone (See Fig. 1, page 12) are not met the sensors will detect a problem and the display will flash with the power level in the affected Cooking Zone Alpha-Numeric display. Any problems must be corrected before proceeding. 2. Touch and hold the key pad for 2 seconds (or until a beep sounds). The Power LED located above the key pad will turn ON. NOTE: If no other key pad is touched within 10 seconds the request to Power ON the cooktop will clear. 3. To start one or more of the Cooking Zones, lightly touch the key pad for the Cooking Zones needed. A beep will sound and the chosen Cooking Zone power level Alpha-Numeric display will show "- -" indicating no power level for the Zone has been set yet. NOTE: If no other key pad is touched within 10 seconds the request to Power ON the Cooktop Zone will clear. 4. Set the desired power level for the Cooking Zone by touching either the or key pad. If the key pad is touched the Cooking Zone will start at a "Power Boost" maximum power level (the Cooking Zone Alpha-Numeric display will indicate Pb and the control will beep once). If the key pad is touched once the Cooking Zone will start at low (the Cooking Zone Alpha-Numeric display will show "Lo" and the control will beep once). NOTE: Touch once, or repeatedly touch the or key pads to adjust or scroll through power levels at any time during the cooking process (To scroll through the power levels quickly touch and hold the or key pads until the power level desired is reached). Once the Cooking Zone power level has been set the food will begin to heat at that level until the power level is manually changed. For more information about the available Cooktop Zones power levels available see "Power Level Settings" section on page 10.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
14
Setting Surface Controls
USING THE TOUCH CONTROL
The recommended way to use the touch pads on the cooktop is with your finger placed in
the center of the touch pad. If the finger is not placed on the center of a pad, the cooktop
may not respond to the selection made.
Lightly contact the pad with the flat part of your entire fingertip. Do not just use the narrow
end of your fingertip.
OPERATING THE COOKING ZONES
The Induction cooktop has four or five Cooking Zones designed for cookware of various sizes.
Be sure to place cookware that meets the minimum and maximum pan size requirements
(see Fig. 2, page 11) for the Cooking Zone desired and is best for the amount of food being
prepared. Place the cookware with the prepared food on the Cooking Zone
BEFORE
setting
any of the Cooktop controls.
To Turn ON one or more of the Cooking Zones:
1.
Place the prepared food using the correct type and size cookware on the desired Cooking
Zone. Be sure to center the cookware on Cooking Zone completely covering the minimum
ring marked on the Zone surface. PLEASE NOTE: If the cookware requirements for the
Cooking Zone (See Fig. 1, page 12) are not met the sensors will detect a problem and
the display will flash with the power level in the affected Cooking Zone Alpha-Numeric
display. Any problems must be corrected before proceeding.
2.
Touch and hold the
key pad for 2 seconds (or until a beep sounds). The Power LED
located above the
key pad will turn ON. NOTE: If no other key pad is touched within
10 seconds the request to Power ON the cooktop will clear.
3.
To start one or more of the Cooking Zones, lightly touch the
key pad for the
Cooking Zones needed. A beep will sound and the chosen Cooking Zone power level
Alpha-Numeric display will show
“
- -
”
indicating no power level for the Zone has been
set yet.
NOTE:
If no other key pad is touched within 10 seconds the request to Power
ON the Cooktop Zone will clear.
4.
Set the desired power level for the Cooking Zone by touching either the
or
key pad. If the
key pad is touched the Cooking Zone will start at a “
Power Boost
”
maximum power level (the Cooking Zone Alpha-Numeric display will indicate
Pb
and the
control will beep once). If the
key pad is touched once the Cooking Zone will start
at low (the Cooking Zone Alpha-Numeric display will show
“
Lo
”
and the control will beep
once).
NOTE:
Touch once, or repeatedly touch the
or
key pads to adjust or scroll
through power levels at any time during the cooking process (To scroll through the power
levels quickly touch and hold the
or
key pads until the power level desired
is reached). Once the Cooking Zone power level has been set the food will begin to heat
at that level until the power level is manually changed. For more information about the
available Cooktop Zones power levels available see “Power Level Settings” section on
page 10.