Electrolux EI30GS55LB Installation Instructions (All Languages) - Page 8

Leveling the Range

Get Electrolux EI30GS55LB PDF manuals and user guides View all Electrolux EI30GS55LB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS (Models with Sealed Top Burners) 8.10 Position range in front of the cabinet opening. 8.11 Make sure that the underside of the cooktop clears the countertop. If necessary, raise the unit by lowering the front leveling legs and the back leveling wheels. 8.12 Level the range (see section 9). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range". 8.13 Slide the range into the cutout opening. 3. Check if the range is level by installing an oven rack in the center of the oven and placing a level on the rack (Figure 8). 4. Take 2 readings with the level placed diagonally in one direction and then the other. Level the range, if necessary, by adjusting the leveling legs and wheels. 5. If the range cannot be level, contact a carpenter to correct sagging or sloping floor. IMPORTANT If Accessories Needed : Installation With Backguard The cutout depth of (21 3/4" (55.2 cm)Min., 22 1/8" (56.2cm) Max.) needs to be increased to 24" (61 cm) when installing a backguard. Installation With End Panel A End Panel kit can be ordered through a Service Center. Installation With Side Panels A Side Panels kit can be ordered through a Service Center. Install cabinet doors 32" (81.3 cm) min. apart so as not to interfere with range door opening. 9 Leveling the Range Models Equipped with Leveling Device Level the range after installation in the cutout opening. 1. Open the range drawer. The leveling screws control the height of the rear leg. 2. Adjust the appliance legs and wheels as follows until the underside of the cooktop surface is sitting level on the countertop (Figure 7). a. To adjust the front legs, use a wrench on the leg base and turn clockwise to lower or counterclockwise to raise. b.Remove the rear legs using a wrench on the leg base and turn counterclockwise until the legs are removed from the unit. You can discard those legs, they are only in place to solidify the unit for the transport. c. To adjust the rear wheels, use a ratchet or a nutdriver and turn the leveling screws counterclockwise to lower or clockwise to raise. Rear Leveling Device Use this Screw to Adjust Rear Leveling Device Height Leveling Screw RAISE Font Leveling Leg LOWER LOWER RAISE Figure 7 RAISE LOWER Figure 8 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
8
30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
(Models with Sealed Top Burners)
Figure 8
RAISE
LOWER
RAISE
RAISE
LOWER
LOWER
Font
Leveling
Leg
Leveling
Screw
Use this Screw
to Adjust Rear Leveling
Device Height
Rear Leveling
Device
Figure 7
IMPORTANT
If Accessories Needed :
8.10
Position range in front of the cabinet opening.
8.11
Make sure that the underside of the cooktop
clears the countertop. If necessary, raise the unit
by lowering the front leveling legs and the back
leveling wheels.
8.12
Level the range
(see section 9). The floor where
the range is to be installed must be level. Follow
the instructions under "Leveling the Range".
8.13
Slide the range into the cutout opening.
Installation With Backguard
The cutout depth of (21 3/4" (55.2 cm)Min., 22 1/8"
(56.2cm) Max.) needs to be increased to 24" (61 cm)
when installing a backguard.
Installation With End Panel
A End Panel kit can be ordered through a Service
Center.
Installation With Side Panels
A Side Panels kit can be ordered through a Service
Center.
Install cabinet doors 32" (81.3 cm) min. apart so as
not to interfere with range door opening.
9
Leveling the Range
Models Equipped with Leveling Device
Level the range after installation in the cutout
opening.
1.
Open the range drawer. The leveling screws control
the height of the rear leg.
2.
Adjust the appliance legs and wheels as follows until
the underside of the cooktop surface is sitting level
on the countertop (Figure 7).
a. To adjust the front legs, use a wrench on
the leg base and turn clockwise to lower or
counterclockwise to raise.
b. Remove the rear legs using a wrench on the leg
base and turn counterclockwise until the legs are
removed from the unit. You can discard those
legs, they are only in place to solidify the unit for
the transport.
c. To adjust the rear wheels, use a ratchet or
a nutdriver and turn the leveling screws
counterclockwise to lower or clockwise to raise.
3.
Check if the range is level by installing an oven rack
in the center of the oven and placing a level on the
rack (Figure 8).
4.
Take 2 readings with the level placed diagonally in
one direction and then the other. Level the range, if
necessary, by adjusting the leveling legs and wheels.
5.
If the range cannot be level, contact a carpenter to
correct sagging or sloping floor.