Electrolux EW27EW55PS Complete Owner's Guide (English) - Page 6

Before Setting Oven Controls

Get Electrolux EW27EW55PS PDF manuals and user guides View all Electrolux EW27EW55PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

6 BEFORE SETTING OVEN CONTROLS Oven Vents The oven vent is located under the control panel. When the oven is on, warm air passes through this vent. This venting is necessary for proper air circulation in the oven and good baking results. Do not block oven vent. Steam or moisture may appear near the oven vent. This is normal. Oven Vent Warm Air Figure 1: Oven vent location Some models are equipped with a cooling fan that runs during the cooking process to cool internal electronic components. It is normal for this fan to continue to run for an extended period of time, even when the oven is off. Figure 2: Do not line the oven walls, racks, bottom, or any other part of the oven with aluminum foil. Doing so will alter heat distribution, produce poor baking results, and may cause permanent damage to the oven interior. During fresh clean temperatures, the oven will be hot enough to melt foil. Oven Rack Supports Always use potholders or oven mitts when removing food or adjusting the oven racks. Wait until the oven in completely cooled if possible. Oven racks may be very hot and may cause burns. To install oven rack supports: Always install the oven rack support before turning on the oven (when the oven is cool). To aid installation of the porcelain oven rack supports, apply a thin layer of cooking oil to all the prongs of the supports (Figure 2). 1. Hold the oven rack support at a slight angle and insert prongs into the holes at the top of the oven cavity (Figure 3). 2. Lift the rack into the top holes, aligning the bottom prongs with the bottom holes (Figure 3). 3. Once the upper prongs are in place, hold the oven rack support flush with the oven side and insert the bottom prongs into the bottom holes (Figure 4). 4. Slide the bottom prongs down into the lower holes. Some force may be required to set the rack into place (Figure 4). To remove the oven rack supports, pull up on the support until lower prongs are out of the holes, hold support at a slight angle and then pull out until the upper prongs are out of the holes. Figure 3: Figure 4: Before Setting Oven Controls

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
6
Before Setting Oven Controls
BEFORE SETTING OVEN CONTROLS
Oven Vents
The oven vent is located under the control panel. When the
oven is on, warm air passes through this vent. This venting is
necessary for proper air circulation in the oven and good baking
results. Do not block oven vent. Steam or moisture may appear
near the oven vent. This is normal.
Some models are equipped with a cooling fan that runs during
the cooking process to cool internal electronic components. It is
normal for this fan to continue to run for an extended period of
time, even when the oven is off.
Do not line the oven walls, racks, bottom, or any other part of the
oven with aluminum foil. Doing so will alter heat distribution,
produce poor baking results, and may cause permanent damage
to the oven interior. During fresh clean temperatures, the oven
will be hot enough to melt foil.
Oven Rack Supports
Always use potholders or oven mitts when removing food or
adjusting the oven racks. Wait until the oven in completely
cooled if possible. Oven racks may be very hot and may cause
burns.
To install oven rack supports:
Always install the oven rack support before turning on the oven
(when the oven is cool).
To aid installation of the porcelain oven rack supports, apply a
thin layer of cooking oil to all the prongs of the supports
(
Figure 2
).
1.
Hold the oven rack support at a slight angle and insert
prongs into the holes at the top of the oven cavity
(
Figure 3
).
2.
Lift the rack into the top holes, aligning the bottom prongs
with the bottom holes (
Figure 3
).
3.
Once the upper prongs are in place, hold the oven rack
support flush with the oven side and insert the bottom
prongs into the bottom holes (
Figure 4
).
4.
Slide the bottom prongs down into the lower holes. Some
force may be required to set the rack into place (
Figure 4
).
To remove the oven rack supports, pull up on the support until
lower prongs are out of the holes, hold support at a slight angle
and then pull out until the upper prongs are out of the holes.
Figure 1:
Oven vent location
Oven Vent
Warm Air
Figure 2:
Figure 3:
Figure 4: