Epson 1660 Start Here Card - Page 1

EPSON Perfection® 1660 Photo SSttaarHrHtteerree 2 Install the Software Wait! You must install your software before connecting the scanner to your computer. The install process may take up to 15 minutes. Be sure to close all open programs and turn off any virus protection programs. Windows® 1 Insert the scanner software CD-ROM in the CD-ROM or DVD drive. The installer starts automatically. If it doesn't start, open My Computer, double-click EPSON, then double-click EPSON. 2 When you see a message asking you to disable antivirus software, click Continue. 3 Read the license agreement, then click Agree. 4 At the Software Installation screen, click Install. 1 Unpack Your Scanner 1 Make sure you have everything: Built-in transparency unit AC adapter Scanner CD-ROM with EPSON® TWAIN driver, software, and electronic manuals Film holder Power cord USB cable See your on-screen Scanner Reference Guide for instructions on scanning slides and negatives. 2 Remove all the packing tape, but leave the yellow sticker in place for now. IMPORTANT! Leave the yellow sticker in place until you're instructed to remove it. Click Install 5 Follow the on-screen instructions to install each program. After each one is installed, click Next or Finish to continue. Note that EPSON Smart Panel™ installs in several steps. If you have PDA software on your computer, Presto! PixExpress will be installed. Please wait until the process is complete. 6 When you see this message, click Yes or No: You see this screen: Click Exit NOTE: Presto! PixExpress will not be installed if you don't have PDA software on your computer. If you add it later, you can install Presto! PixExpress. See your on-screen Scanner Reference Guide for instructions. 7 Click Exit. The EPSON Product Registration screen appears. 8 Register your scanner as instructed. At the last screen, click Done or close your browser. Then follow the instructions in section 3 to connect the scanner. Macintosh® 1 Insert the scanner software CD-ROM in the CD-ROM or DVD drive. (If necessary, double-click the EPSON CD-ROM icon to open it.) 2 Double-click . 3 When you see a message asking you to disable antivirus software, click OK. 4 Read the license agreement, then click Agree. 5 When the Software Installation screen appears, click Install. 3 Connect the Scanner After your software is installed, it's time to get connected! 1 Remove the yellow sticker from the back of the scanner. Remove the yellow sticker You see the EPSON TWAIN 5 Installer: Click Install Click install 6 Click Install. When the EPSON TWAIN installation is complete, click Restart. Don't remove your CD-ROM. After your Macintosh restarts, you can install the rest of your software. 7 When your Macintosh restarts, double-click the EPSON CD-ROM icon to open it, if necessary, then double-click . You see this screen: Click Install 8 Click Install and follow the on-screen instructions to install each program. After each one is installed, click Quit to continue. Note that EPSON Smart Panel installs in several steps. If you have PDA software on your computer, Presto! PixExpress will be installed. 9 When you see this message, click Yes or No: You see this screen: 2 Connect the cable for the built-in transparency unit to the connector on the back of the scanner. 3 Slide the transportation lock all the way to the right. 4 Connect the power cord and AC adapter, as shown. Transportation lock AC adapter Power cord 5 Connect the AC adapter to the scanner. 6 Plug the other end of the power cord into an electrical outlet. The scanner turns on and begins to warm up. The Start button on the front of the scanner flashes. It stops flashing and turns green when the scanner is ready. Start button AC adapter 7 Plug the square end of the USB cable into the scanner's USB port. Click Exit NOTE: Presto! PixExpress will not be installed if you don't have PDA software on your computer. If you add it later, you can install Presto! PixExpress. See your on-screen Scanner Reference Guide for instructions. 10 Click Exit. The EPSON Product Registration screen appears. 11 Register your scanner as instructed. At the last screen, click Done or close your browser. Then follow the instructions in section 3 to connect the scanner. 8 Plug the flat end of the cable into any available USB port on your computer. NOTE: Your system may not work correctly if you use a USB cable other than the one supplied by EPSON or if you connect to your computer through a hub. Now you're ready to start scanning! Turn this sheet over for step-by-step instructions. Turn Over