Epson 585W Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43)
Epson 585W Manual
View all Epson 585W manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson 585W manual content summary:
- Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 1
Installation Guide Guide d'installation - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 2
Pad and Touch Unit after wall mount installation. The following projectors are covered by this guide: • BrightLink® 475Wi/480i/485Wi/575Wi/585Wi/595Wi and 575Wi+/585Wi+/595Wi+ • BrightLink Pro 1410Wi/1420Wi/1430Wi • PowerLite® 470/475W/480/485W/570/575W/580/585W Safety Instructions For your safety - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 3
service personnel. If you need to loosen any screws during installation, be careful not to drop the wall mount. If the wall mount or projector falls, it could cause personal injury or property damage. Install the wall mount so that it can sufficiently support the weight of the projector and wall - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 4
which could cause medical equipment to malfunction. Caution Do not install the wall mount in a location where the operating temperature for your projector model may be exceeded. Such an environment may damage the projector. Install the wall mount in a place free from excessive dust and humidity to - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 5
smooth, and unwarped with no more than 0.2 inches (5 mm) of unevenness in any direction on the screen surface. 0.2 in. (5 mm) • When installing on a whiteboard, install the Touch Unit within the frame of the whiteboard. Correct position Incorrect position Make sure there are no obstacles, such as - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 6
Contents s8 2 Specifications s 10 3 Connecting Devices s 14 4 Positioning the Projector s 16 1. Installation worksheet for projecting on a pre-installed wall-mounted board 2. Installation worksheet for projecting on a plain wall 3. Diagonal image size and mounting position 4. Distance - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 7
the Covers 1. Attach the wall plate cover and end cap 2. Attach the cable cover to the projector s 47 8 Installing the Touch Unit 1. Turn on the projector 2. Display the installation pattern 3. Remove the markers 4. Determine the installation position for the Touch Unit 5. Install the Touch Unit - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 8
wall plate assembly For 3-axis adjustment unit/wall mount installation For slide plate/projector installation For slide plate/3-axis adjustment unit installation (secured when shipped) For wall mount/wall plate installation supplied with the wall mount to install it as directed in this guide. Do not - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 9
deflector (approx. 11.2 inches [28.5 cm]) (×8) Control Pad The following parts are packaged with your projector and are necessary when attaching the Control Pad. When installing the Control Pad on a wall, you will also need four M4 × 20 mm screws. Control Pad AA size batteries (× 2) Rubber - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 10
to the illustration on page 11 s p. 44 s p. 44 s p. 45 Wall plate The wall plate is in three pieces when shipped. Use the included M4 × 12 mm bolts (×6) to attach the separate pieces together before mounting the projector. See page 31 for instructions. 3.1 in. (79 mm) 6.3 in. (160 mm) 8.4 in. (213 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 11
unit to the front or back, you can adjust the installation position of the projector. When the screen size is less than 75 inches, install it at the position marked with a stamp on the mount arm. When the screen size is 75 inches or more, install it at the position marked with a arm. stamp on - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 12
Touch Unit External dimensions and weight The Touch Unit weighs approximately 16 ounces (450 g). 3.7 in. (95 mm) 8.3 in. (210 mm) 2.0 in. (51 mm) Attached labels The Touch Unit is a Class 1 laser product that conforms to the JIS C 6802:2011 standard. There are warning labels affixed to the Touch - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 13
mm) 5.9 in (149 mm) 6.0 in (153.5 mm) 0,6 in (15.47 mm) 1.1 in (29 mm) 1.2 in (30.9 mm) Cable routing holes When routing cables through a wall, use the position ( ) in the following figure as the cable routing hole. Otherwise, remove the cable cover ( ) and route the cables through the opening - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 14
and other parts at the location where the wall mount is to be installed. Make sure you also have all necessary cables for the Touch Unit and other devices, such as a document camera or microphone, that you will connect to the projector. Your projector's connection panel may differ slightly from the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 15
the BrightLink Pro 1410Wi/1420Wi/1430Wi projectors. It provides a convenient alternative to the remote control for turning on the projector, changing the source, and selecting whiteboard mode. You can also use the control pad to capture, print, and save your projected images. You must install the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 16
determines the maximum image size and how high the image appears on the wall or whiteboard. The distance of the projector from the wall (once it is mounted on the adjustable arm of the wall mount) also affects image size and position. If you are planning to project on a whiteboard, the image may - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 17
for projecting on a pre-installed wall-mounted board 1. Measure the wall plate. 11. Align the line (horizontal) on the template sheet with the (c) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 30 to install the projector - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 18
Installation worksheet for projecting on a plain wall 1. Measure the ceiling height (distance from the floor to the ceiling). _____ 2. Determine the desired aspect ratio of the image. For new computers or laptops, - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 19
Follow the instructions on page 30 to install the projector. The tables on the following pages provide installation information for all supported image following pages to determine the projection distance and placement of the wall plate. The recommended range for projection distance (a) as shown on - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 20
plate Notch on mount arm Installation measurement tables Use the following table to determine which installation measurement table to use for your projector. Projector model Maximum image size (diagonal) Installation measurement table BrightLink Pro 1410Wi/1420Wi/1430Wi BrightLink 475W/485W - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 21
21 Installation Measurements in Inches for WXGA Projectors Diagonal image size (S) Min. ceiling height* Image width (w) 16:10 WXGA Image Min. Slider height projection scale (h) distance mark (a) (b) Distance Min. from top of ceiling image to height* wall plate holes (c) Image width (w) - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 22
height* Image width (w) 16:9 Widescreen Image height (h) Min. projection distance (a) Slider scale mark (b) Distance from top of image to wall plate holes (c) 77" 89.5 65.3 40.8 6.6 6.6 8.6 95.9 61.6 46.2 9.1 9.1 9.7 88.7 67.1 37.8 7.1 7.1 11.0 78" 90.1 66.1 41.3 6.9 6.9 8.8 96.6 62 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 23
23 Installation Measurements in Inches for XGA Projectors Diagonal image size (S) Min. ceiling height* Image width (w) 4:3 XGA Image Min. Slider Distance height projection scale from top of (h) distance (a) mark image to (b) wall plate holes (c) 16:10 WXGA Min. Image Image Min. ceiling width - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 24
(S) Min. ceiling height* Image width (w) 4:3 XGA Image Min. Slider Distance height projection scale from top of (h) distance (a) mark image to (b) wall plate holes (c) 16:10 WXGA Min. Image Image Min. ceiling width height projectio height* (w) (h) n distance (a) Slider Distance scale from top - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 25
25 Installation Measurements in Millimeters for WXGA Projectors Diagonal image size (S) Min. ceiling height* 16:10 WXGA Image Image Min. width height projection (w) (h) distance (a) Slider scale mark (b) Distance from top of image to wall plate holes (c) Min. ceiling height* Image width (w) - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 26
plate holes (c) Min. ceiling height* 16:9 Widescreen Image Image Min. Slider Distance width height Projection scale from top of (w) (h) distance mark image to (a) (b) wall plate holes (c) 77" 2272 1659 1037 168 168 219 2436 1565 1173 231 231 247 2253 1705 959 181 181 278 78" 2288 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 27
27 nstallation Measurements in Millimeters for XGA Projectors Diagonal image size (S) 4:3 XGA Min. Image Image Min. ceiling width height projection height* (w) (h) distance (a) Slider Distance scale from top of mark image to (b) wall plate holes (c) Min. ceiling height* 16:10 WXGA Image Image - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 28
plate holes (c) Min. ceiling height* 16:9 Widescreen Image Image Min. Slider Distance width height Projection scale from top of (w) (h) distance mark image to (a) (b) wall plate holes (c) 75" 2357 1524 1143 189 189 198 2336 1615 1010 219 219 310 2320 1660 934 234 234 370 76" 2375 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 29
interactive whiteboard, refer to the table below to identify common models and sizes. If your board is listed here, use the dimensions to reference the installation requirements found on pages 21 to 28. Diagonal size 57 inches 60 inches 63 inches 64 inches 66 inches 71 inches 75 inches 77 inches - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 30
. ❏ The maximum combined weight of the projector and the wall mount is 32.6 lb (14.8 kg). ❏ Do not hang the rest of the cable over the wall mount. ❏ Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and resist any horizontal vibration. Use M10 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 31
the parts 1. Assemble the wall plate. Assemble the three plates into one unit, and secure them with the M4 × 12 mm hexagon socket head cap bolts (×6) supplied. Washer Spring washer M4 × 12 mm hexagon socket head cap bolts 2. Attach the slide plate to the projector. Attach the slide plate to - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 32
3. Attach the 3-axis adjustment unit to the wall mount. • Decide which position you want to use for installing the 3-axis adjustment unit. Mount it at the stamp when the image is less than 75 inches (diagonally), or at the when the projected image is 75 inches or more ( - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 33
. (70.5 mm) Image Center line of template sheet line of template sheet Center line of projection surface 2. Attach the template sheet to the wall. If you need to install a junction box, you can use the cutout areas in the wall plate for the box. The junction box needs to be recessed into the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 34
in three places, drill the holes indicated by C in the illustration below. Four mounting holes Three mounting holes Steps 4 to 8 below provide instructions for attaching the wall plate to a concrete wall. 4. Drill holes of the following diameters and depths. Drill diameter Pilot hole depth - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 35
the number for the slider measure (b). 2. Loosen the M4 × 12 mm hexagon socket head cap bolts (×2), and then pull out the slider on the wall mount. Align the slider with the measure (b+x) that is equal to the slider measure (b) plus the thickness of the projection screen (x). For an illustration of - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 36
E Route the cables through the wall mount arm Touch Unit connection cable BrightLink 595Wi/595Wi+ and BrightLink Pro 1430Wi: Make sure to route the Touch Unit connection cable through the wall mount arm. Route the Touch Unit connection cable so that the end that connects to the Touch Unit appears - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 37
with the other cables. ❏ Take care not to trap the cables between the mount arm and wall plate. Hexagonal shaft Touch Unit connection cable M8 hexagonal bolt 4. Secure the mount arm to the wall plate by tightening the supplied M6 × 20 mm cross recessed head shoulder screws (×3) with the No.3 cross - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 38
M8 hexagon bolt at the bottom of the wall mount, or the hexagonal shaft at the top of the wall mount ( ). Start by aligning the notch on the arm with the stamp on the wall plate as shown below. Tightening the M8 hexagon bolt lowers the wall mount, and loosening the bolt raises it. Tightening the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 39
Washer Spring washer M4 × 12 mm hexagon socket head cap bolts Alignment marks Warning When installing or adjusting the wall mount, do not use adhesives to prevent the screws from loosening and do not use lubricants or oils on the projector slide plate. This may cause the case to crack and the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 40
cable, Control Pad cables, and power cord to the projector. See your projector's User Guide for detailed connection information. Power cord Computer cable USB cable Touch Unit connection cable Connect the power cord last. BrightLink 595Wi/595Wi+: When connecting to the Audio1, Audio2, and - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 41
model Remote control column PowerLite 470/480/570/580 BrightLink 475W/480i/485W/575Wi/585Wi/595Wi A BrightLink 575Wi+/585Wi+/595Wi+ PowerLite 475W/485W/575W/585W BrightLink Pro 1410Wi/1420Wi/1430Wi B A Turn on the projector Using the Remote Control A Using the Remote Control B Using - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 42
The test pattern contains a guide to help you adjust the displayed image if your screen's aspect ratio is the same as the projector's native aspect ratio. C menu - Aspect. Following is a list of available aspect settings: BrightLink 480i and PowerLite 570/580 • Auto: Automatically sets the aspect - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 43
Pro 1410Wi/1420Wi/1430Wi, BrightLink 575Wi/575Wi+/585Wi/585Wi+/595Wi/ 595Wi+, and PowerLite 575W . s Projector User's Guide: Signal Menu D Adjust the focus 1. Slide the air filter cover switch ( ) to open the air filter cover ( ). 2. Use the focus lever to adjust the focus ( ). Focus lever Air - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 44
E Use the adjustment knob on the left side to adjust the horizontal roll E J Repeat steps to as necessary. For each step, you may need to re-display the B test pattern as shown in step . 1. Loosen the screw ( ) to unlock the adjustment knob. Screw 2. Turn the orange knob ( ) to adjust the horizontal - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 45
English 2. Turn the dark blue knob ( ) to adjust the horizontal rotation ( ). E J 3. After you finish making all of the adjustments in steps to , tighten the screws (x2) you loosened in . G Use the adjustment knob on the top to adjust the vertical tilt 1. Loosen the screw ( ) to unlock the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 46
head cap bolts (×2). I Adjust the forward/backward slide 1. Loosen the M4 × 12 mm hexagon socket head cap bolts (×2), and then adjust the slider for the wall mount. M4 × 12 mm hexagon socket head cap bolts (x2) E J 2. After you finish making all of the adjustments in steps to , tighten the M4 × 12 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 47
. Otherwise, the projector or wall mount may fall and cause personal injury or property damage. 7 Attaching the Covers A Attach the wall plate cover and end cap If you need to use a security cable, make sure you attach it before installing the wall plate cover. See page 66 for instructions. You can - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 48
maintenance and repairs. Refer to your projector's User's Guide for instructions on maintenance and repairs. Warning ❏ Never loosen the bolts and nuts after installation. If you find any loose screws, tighten them firmly. Otherwise, the projector or wall mount may fall and cause personal injury or - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 49
must have been completed before installing the Touch Unit: • Installing the projector (see page 30) • Adjusting the projected image (see page 41) • Calibrating the interactive pen(s) s Refer to your projector User's Guide or Start Here folder for detailed instructions. ❏ There are magnets built in - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 50
2. Select Touch Unit Setup. 3. Select Installation Pattern. The Installation pattern is displayed on the projected image. C Remove the markers 1. Loosen the screw at the bottom of the dial cover. 50 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 51
Touch Unit. Use the markers to perform the angle adjustment (p. 53) after installing the Touch Unit. D Determine the installation position for the Touch Unit Mark the following installation positions: • ( ): The center line of the installation pattern; align it with the center line of the Touch Unit - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 52
of the Touch Unit on the screen surface to secure it. Caution When installing the Touch Unit on a magnetic surface, be careful not to trap your fingers or any other part of your body between the magnets and the installation surface. • For non-magnetic screens, secure the Touch Unit with three (3) M4 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 53
the interactive pen(s) before adjusting the angle. Press the User button on the remote control and select Yes to perform an auto-calibration. Refer to the projector's User's Guide for detailed instructions on calibrating the pen(s). 1. Select Easy Interactive Function from the Extended menu - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 54
2. Select Touch Unit Setup. 3. Select Power and set to On. The Touch Unit power turns on and the indicator light turns blue. Indicator light Warning Do not look into the projector's projection window or the Touch Unit's laser diffusion ports (located on the back of the Touch Unit); this could cause - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 55
English 4. Select Angle Adjustment. The Angle Adjustment screen is displayed. 5. Turn the adjustment dials on the Touch Unit counterclockwise until you hear a click. Then, press the button on the remote control. When adjusting the dials, make sure to stop turning when you hear the click. 55 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 56
6. Attach the two markers you removed from the Touch Unit to the marker positions shown on the projected screen ( ) ( ). Blue marker position Green marker position Match the positions so that the crosses ( ) overlap with the points ( ) on the marker positions ( ) ( ). Move the marker over the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 57
English Do not place anything other than the markers near the projected image during angle adjustment. If other objects are on the projected image, angle adjustment may not be performed correctly. 7. Turn the adjustment dials on the Touch Unit to move the pointers ( ) ( ) so that they move inside - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 58
8. When the pointers on the left and right become solid colors ( ) ( ), press the button on the remote control. The following screen is displayed: 9. Place the markers at the top marker positions [1]. When angle adjustment is performed correctly, the upper pointers become solid colors ( ) ( ). If - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 59
English 11. When you have finished checking the marker positions, remove the markers and press the button on the remote control. The following confirmation screen is displayed: 12. Trace the dots with your finger as shown. When angle adjustment is performed correctly, the traced dots disappear. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 60
or button on the remote control, and then repeat step 12 again. If the dots do not disappear even after performing the above procedures, contact Epson. 60 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 61
by pressing Menu on the remote control. On the Extended menu, select Easy Interactive Function, then Touch Unit Setup. Select Touch Calibration and follow the instructions. H Store the markers and attach labels 1. Store the markers inside the Touch Unit. 2. Attach the labels to the tabs on - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 62
. Caution The Control Pad should only be connected to the BrightLink Pro 1410Wi/1420Wi/1430Wi. Do not connect the Control Pad to any other projectors. Check the installation location The Control Pad must be installed in the area specified in the diagram below. 78.7 in. 68.9 in. 35.4 in. 27 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 63
attach the Control Pad with double-side tape or magnets. ❏ Check that the Control Pad is operating correctly before attaching it with the screws. ❏ When installing the Control Pad on a table, attach the supplied rubber feet (x4) to the base of the Control Pad to prevent it from slipping. 63 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 64
C Install the batteries Caution Before handling the batteries, read the safety instructions in your projector's User's Guide. ❏ Use two AA manganese or alkaline (recommended) batteries. Do not use any other type of battery. Rechargable batteries cannot be used. ❏ In order to use the projector to - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 65
function Required cables Projecting images from a USB flash drive Saving data to a USB flash drive USB cable 1 Supplying power from the projector Remote control cable set (model ELPKC28; part number V12H005C28) Projecting computer images with USB Display or performing mouse functions using the - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 66
X users also need to install a driver that enables pen or finger touch interactivity to work. Both software programs are included with the BrightLink projector. For details, see the online User's Guide or visit: U.S.: epson.com/support/brightlinkdownloads Canada: epson.ca/support/brightlinkdownloads - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 67
boîtier de commande et l'unité tactile après l'installation du support mural. Ce guide fournit les explications pour les projecteurs suivants : • BrightLink® 475Wi/480i/485Wi/575Wi/585Wi/595Wi et 575Wi+/585Wi+/595Wi+ • BrightLink Pro 1410Wi/1420Wi/1430Wi • PowerLite® 470/475W/480/485W/570/575W/580 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 68
Avertissement Suivez les instructions du présent guide pour installer le support de montage. En cas de non-respect des instructions, le support de montage peut tomber et provoquer des blessures corporelles ou des dommages matériels. Suivez les instructions du présent guide pour installer et utiliser - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 69
oculaires. Connectez l'unité tactile aux modèles BrightLink 595Wi/595Wi+ et BrightLink Pro 1430Wi seulement. Ne connectez pas l'unité à d' supports. Emplacement pour l'installation • Avant d'installer le projecteur, vérifiez le câblage de l'alimentation électrique de l'emplacement d'installation - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 70
• Monté verticalement sur une table avec la projection d'images depuis le devant de la table. Si vous utilisez cette méthode d'installation, vous aurez besoin du support pour table interactive en option (ELPMB29) et de la plaque de fixation (ELPPT05). • Lorsque le boîtier de commande est alimenté - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 71
Français • Assurez-vous qu'il n'y a pas d'obstacles, par exemple des câbles ou des objets protubérants comme des plateaux pour tableau blanc ou des cadres épais dans les zones ombrées de l'illustration ci-dessous. L'unité tactile ne fonctionnera pas correctement si le signal infrarouge est bloqué. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 72
ètres pour les projecteurs XGA 5 Installation du projecteur 1. Désassemblez les pièces 2. Assemblez les pièces 3. Installez la plaque murale sur le mur 4. Déterminez la distance de projection et retirez la glissière 5. Faites passer les câbles dans le bras du support de montage 6. Fixez le bras - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 73
glez le coulissement vertical 11. Supprimez l'affichage de la mire 7 Fixation des caches 1. Fixez le cache du support de montage et le capuchon de protection 2. Fixez le cache du câble au projecteur s 121 8 Installation de l'unité tactile 1. Mettez le projecteur sous tension 2. Affichez le motif - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 74
74 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 75
de montage/plaque murale Vis à épaulement à tête à empreinte cruciforme 3 M6 x 20 mm avec rondelle plastique • Utilisez les vis ou les boulons fournis avec le support de montage pour installer ce dernier, comme décrit dans le présent guide. Ne leur substituez pas un autre type de boulons. 75 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 76
, incluant un tournevis cruciforme numéro 3. Unité tactile Les pièces suivantes sont emballées avec votre projecteur et sont nécessaires lors de l'installation de l'unité tactile. Lorsque vous installez l'unité tactile sur une surface non magnétique, vous aurez aussi besoin de vis M4. Unité tactile - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 77
verticale Information supplémentaire Page de référence Support de montage : 3,0 kg (6,6 lb) po) Réglage à partir de la position d'installation du dispositif de réglage à 3 axes : le montage du projecteur. Consultez la page 104 pour obtenir les instructions. 79 mm (3,1po) 160 mm (6,3 po) 213 mm - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 78
vers l'avant/l'arrière Plage de réglage du coulissement du bras 273 mm (10,7 po) Réglage à partir de la position d'installation du dispositif de réglage à 3 axes En déplaçant la position d'installation du dispositif de réglage à 3 axes vers l'avant ou l'arrière, vous pouvez régler la position - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 79
95 mm (3,7 po) Français Pour voir le poinçon, vous devez retirer les deux vis placées dans le haut et ensuite, faire glisser la rallonge du bras. Poinçon Poinçon Unité tactile Dimensions externes et poids L'unité tactile pèse environ 450 g (16 oz). 87 mm (3,4 po) 210 mm (8,3 po) 51 mm (2,0 mm) - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 80
Port de diffusion du laser Le faisceau laser est diffusé depuis les ports de diffusion laser à l'arrière de l'unité tactile. Ports de diffusion laser Boîtier de commande Dimensions externes et poids Le boîtier de commande pèse environ 240 g (8,5 oz). 135,9 mm (5,4 po) 11,5 mm (0,4 po) 111 mm (4,4 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 81
Français Sinon, retirez le cache-câbles ( ) et faites passer les câbles à travers l'ouverture. Faites passer le câble de l'imprimante le long de la rainure à l'arrière du boîtier de commande 81 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 82
les autres pièces à l'emplacement d'installation du support de montage. Assurez-vous aussi d'avoir Pour obtenir plus de détails, consultez le Guide de l'utilisateur en ligne pour votre projecteur. audio (non inclus) Microphone Caméra de documents (Epson DC-06) Unité tactile Câble réseau local - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 83
Installation du boîtier de commande p. 136 pour les instructions. 4 Positionnement du projecteur Les projecteurs BrightLink Pro 1410Wi/1420Wi/1430Wi, BrightLink 475W/485W, BrightLink 575Wi/585Wi/ 595Wi, BrightLink il est monté sur le bras réglable du support de montage) influe aussi sur la taille et - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 84
murale sur le mur. Si vous projetez sur un tableau blanc préinstallé, utilisez la feuille de travail à la page suivante. Si vous mur ordinaire, utilisez la feuille de travail de la page 86. Lors de l'installation sur un tableau blanc, assurez-vous de laisser les écarts suivants autour du bord - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 85
s'agira probablement de XGA (4:3). Il vous faudra peutêtre consulter le service des TI pour obtenir cette information. ___ 4:3 XGA ___ 16:10 le bas de la plaque murale (c). 9. Déterminez la position pour l'installation de votre projecteur en additionnant les _____ (f) valeurs (f), (h) et (c), - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 86
Suivez les directives de la page 103 pour installer le projecteur. Feuille de travail d'installation pour la projection sur un mur ordinaire il s'agira probablement de XGA (4:3). Il vous faudra peut-être consulter votre service des TI pour obtenir cette information. ___ 4:3 XGA ___ 16:10 WXGA - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 87
centrale du gabarit avec le centre de la zone d'image. Suivez les directives de la page 103 pour installer le projecteur. Les tableaux des pages suivantes fournissent des renseignements d'installation pour toutes les tailles d'image prises en charge. La hauteur de plafond minimum est basée sur une - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 88
Décalage pour la position du centre de l'écran et le centre de la plaque murale 70,5 mm (2,8 po) 218 mm (8,6 po) 120 mm (4,7 po) Plaque murale 30,6 mm (1,2 po) Hauteur de l'image projetée 100 mm (4 po) 25 mm (1 po) Distance du mur à la surface 20 mm (0,8 po) de projection Surface de - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 89
le bras du support Tableaux des mesures d'installation Utilisez le tableau suivant afin de déterminer quel tableau de mesures vous devez utiliser pour votre projecteur. Modèle du projecteur BrightLink Pro 1410Wi/1420Wi/1430Wi BrightLink 475W/485W/575Wi/585Wi/595Wi BrightLink 575Wi+/585Wi+/595Wi - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 90
Mesures d'installation en pouces pour les projecteurs WXGA 90 Taille de l'image diagonale (S) Hauteur du plafond min.* 16:10 WXGA Largeur Hauteur Dist. de de de proj. l' - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 91
91 Taille de 16:10 WXGA 4:3 XGA 16:9 grand écran l'image Hauteur Largeur Hauteur Dist. de Repères Dist. du Hauteur Largeur Hauteur Dist. de Repères Dist. du Hauteur Largeur Hauteur Dist. de Repères Dist. du diagonale du de de proj. de haut de du de de proj. de haut de du de de proj. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 92
Taille de l'image diagonale (S) Hauteur du plafond min.* 16:10 WXGA Largeur Hauteur Dist. de de de proj. l'image l'image min. (a) (l) (h) Repères de glissière (b) Dist. du haut de l'image aux trous de la plaque murale (c) Hauteur du plafond min.* Largeur de l'image (l) 4:3 XGA Hauteur - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 93
93 Mesures d'installation en pouces pour les projecteurs XGA Taille de 4:3 XGA 16:10 WXGA 16:9 grand écran l'image Hauteur Largeur Hauteur Dist. de Repères Dist. du - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 94
Taille de 4:3 XGA 16:10 WXGA 16:9 grand écran l'image diagonale Hauteur du Largeur de Hauteur de Dist. de proj. Repères de Dist. du haut de Hauteur Largeur du de Hauteur Dist. de Repères de proj. de Dist. du haut de Hauteur Largeur Hauteur Dist. de du de de proj. Repères de - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 95
Taille de 4:3 XGA 16:10 WXGA 16:9 grand écran l'image Hauteur Largeur Hauteur Dist. de Repères Dist. du Hauteur Largeur Hauteur Dist. de Repères Dist. du Hauteur Largeur Hauteur Dist. de Repères Dist. du diagonale du de de proj. de haut de du de de proj. de haut de du de de proj. de - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 96
Mesures d'installation en millimètres pour les projecteurs WXGA Taille de l'image diag. (S) Haut. du plafond min.* Larg. de l'image (l) 16:10 WXGA Haut. de Dist. de l' - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 97
97 Taille de l'image diag. (S) Haut. du plafond min.* Larg. de l'image (l) 16:10 WXGA Haut. de Dist. de l'image proj. (h) min. (a) Repères de glissière (b) 4:3 XGA Dist. du haut de l'image aux trous de la plaque murale (c) Haut. du plafond min.* Larg. de l'image (l) Haut. de l'image (h) - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 98
Taille de l'image diag. (S) Haut. du plafond min.* Larg. de l'image (l) 16:10 WXGA Haut. de Dist. de l'image proj. (h) min. (a) Repères de glissière (b) 4:3 XGA Dist. du haut de l'image aux trous de la plaque murale (c) Haut. du plafond min.* Larg. de l'image (l) Haut. de l'image (h) Dist. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 99
99 Mesures d'installation en millimètres pour les projecteurs XGA Taille de l'image diag. (S) Haut. du plafond min.* 4:3 XGA Larg. de l'image (l) Haut. de l'image (h) Dist. de proj. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 100
100 Taille de l'image diag. (S) Haut. du plafond min.* 4:3 XGA Larg. de l'image (l) Haut. de l'image (h) Dist. de proj. min. (a) 71 po 72 po 73 po 74 po 75 po 76 po 77 po 78 po 79 po 80 po 81 po 82 po 83 po 84 po 85 po 86 po 87 po 88 po 89 po 90 po 2286 2304 2322 2340 2357 2375 2392 2411 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 101
Taille de l'image diag. (S) 4:3 XGA Haut. du plafond min.* Larg. de l'image (l) Haut. de l'image (h) Dist. de proj. min. (a) Repères de glissière (b) 16:10 WXGA Dist. du haut de l'image aux trous de la plaque murale (c) Haut. du plafond min.* Larg. de l'image (l) Haut. de l'image (h) - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 102
pour identifier les modèles et tailles communes. Si votre tableau est listé ici, utilisez les dimensions pour vous référer aux exigences d'installation des pages 90 à 96. Tailles des tableaux blancs interactifs Taille diagonale 16:10 WXGA 4:3 XGA 16:9 grand écran 57 po - PolyVision TS410 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 103
écrous et des boulons de taille inférieure à M10, le support de montage risque de tomber. ❏ Epson n'accepte aucune responsabilité pour tout dommage ou toute blessure dus à une solidité du mur insuffisante ou une installation inappropriée. A Désassemblez les pièces Retirez la plaque coulissante du - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 104
tête cylindrique à six pans M4 x 12 mm Rondelle élastique Rondelle 3. Fixez le dispositif de réglage à 3 axes au support de montage. • Choisissez la position selon laquelle vous souhaitez installer le dispositif de réglage à 3 axes. Installez-le au niveau du poinçon lorsque l'image est inférieure - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 105
les boulons à tête cylindrique à six pans M4 x 12 mm (x4) fournis pour installer le dispositif de réglage à 3 axes. Boulons à tête cylindrique à six pans M4 x 12 mm Rondelle élastique Rondelle Positions d'installation des boulons Lorsque l'image diagonale est inférieure à 75 po (190,5 cm) Lorsque - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 106
,5 mm (2,8 po) Ligne de la fiche modèle Ligne centrale de la surface de projection 2. Fixez la fiche modèle au mur. Si vous devez installer une boîte de jonction, vous pouvez utiliser les zones de découpe de la plaque murale pour la boîte. La boîte de jonction - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 107
, percez les trous indiqués par C sur l'illustration ci-dessous. Quatre trous de montage Trois trous de montage Les étapes 4 à 8 ci-dessous fournissent les instructions pour fixer la plaque murale à un mur de béton. 4. Percez des trous des diamètres et des profondeurs suivants. Diamètre de per - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 108
mesure de la glissière (b). 2. Desserrez les boulons à tête cylindrique à six pans M4 x 12 mm (x2), puis retirez la glissière sur le support de montage. Alignez la glissière avec la mesure (b+x) équivalente à la mesure de la glissière (b) additionnée à l'épaisseur de l'écran de projection (x). Pour - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 109
de montage Câble de connexion de l'unité tactile Pour les projecteurs BrightLink 595Wi/595Wi+ et BrightLink Pro 1430Wi : Assurez-vous de faire passer le câble de connexion de l'unité tactile dans le bras du support de montage. Faites passer le câble de connexion de l'unité tactile afin que l'extr - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 110
de montage et la plaque murale. Arbre hexagonal Câble de connexion de l'unité tactile Boulon à six pans M8 4. Fixez le bras du support de montage à la plaque murale en serrant les vis à épaulement à tête à empreinte cruciforme M6 x 20 mm (x3) fournies à l'aide du tournevis cruciforme n°3 ( ). Puis - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 111
du bras 1. Réglez le coulissement vertical à l'aide du boulon à six pans M8 sur la partie inférieure du support de montage, ou de l'arbre hexagonal sur la partie supérieure de la plaque d'installation ( ). Commencez par aligner l'encoche sur le bras avec le poinçon sur la plaque murale tel qu - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 112
x 12 mm Marques d'alignement Avertissement Lorsque vous installez ou ajustez le support de montage, n'utilisez pas d'adhésifs afin d'éviter que les vis ne se desserrent et n'utilisez pas d'huiles ou lubrifiants pour la plaque d'installation du projecteur. Le boîtier risque de se détériorer et le - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 113
commande et le cordon d'alimentation au projecteur. Consultez le Guide de l'utilisateur de votre projecteur pour obtenir des informations Audio1, Audio2, puis Computer1. Pour les projecteurs BrightLink Pro 1420Wi/1430Wi : Lorsque vous branchez un câble au port Epson (numéro de pièce : ELPCK01). 113 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 114
ée. Modèle du projecteur Colonne de la télécommande PowerLite 470/480/570/580 BrightLink 475W/480i/485W/575Wi/585Wi/595Wi A BrightLink 575Wi+/585Wi+/595Wi+ PowerLite 475W/485W/575W/585W BrightLink Pro 1410Wi/1420Wi/1430Wi B A Mettez le projecteur sous tension Avec la télécommande A Avec la - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 115
ou sur le bouton [Wide] du panneau de commande. La mire s'affiche. Avec la télécommande A/B Avec le panneau de commande La mire contient un guide afin de vous aider à régler l'image affichée si le rapport hauteur/largeur de l'écran est le même que le rapport hauteur/largeur natif du projecteur - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 116
étirées horizontalement pour tenir à l'écran. BrightLink Pro 1410Wi/1420Wi/1430Wi, BrightLink 575Wi/575Wi+/585Wi/585Wi+/595Wi/ 595Wi+ et PowerLite apparaître ou les images peuvent être rognées, selon la résolution. s Guide de l'utilisateur du projecteur : Menu Signal D Réglez la mise au point 1. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 117
Français E Utilisez la poignée de réglage sur le côté gauche pour régler le roulis horizontal E J Répétez les étapes à tel que nécessaire. Pour chaque étape, il est possible que B vous deviez afficher la mire de nouveau tel qu'illustré à l'étape . 1. Desserrez la vis ( ) pour déverrouiller la poign - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 118
F Utilisez la poignée de réglage sur le côté droit pour régler la rotation horizontale 1. Desserrez les vis (x2) pour déverrouiller la poignée de réglage ( ). Vis (x2) 2. Tournez la poignée bleu foncé ( ) pour régler le roulis horizontal ( ). E J 3. Une fois tous les réglages des étapes à terminés, - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 119
glez le coulissement vers l'avant/l'arrière 1. Desserrez les boulons à tête cylindrique à six pans M4 x 12 mm (x2), puis réglez la glissière du support de montage. Boulons à tête cylindrique à six pans M4 x 12 mm (x2) E J 2. Une fois tous les réglages des étapes à terminés, serrez les boulons à tête - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 120
Appuyez sur le bouton [Esc] de la télécommande ou du panneau de commande pour supprimer la mire. Avertissement Serrez fermement toutes les vis. Sinon, le support de montage ou le projecteur pourrait tomber et provoquer des blessures corporelles ou des dommages matériels. 120 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 121
Fixation des caches A Fixez le cache du support de montage et le capuchon de protection Si vous devez utiliser un câble de sécurité, assurez-vous de le fixer avant d'installer le cache de la plaque murale. Consultez la page 140 pour obtenir les instructions. Vous pouvez utiliser la rallonge du capot - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 122
-vous au Guide de l'utilisateur en ligne de votre projecteur pour plus d'informations sur l'entretien et les réparations. Avertissement ❏ Ne desserrez jamais les écrous et les boulons après l'installation. Si vous constatez le moindre jeu, resserrez fermement les vis concernées. Sinon, le support de - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 123
de certains menus soit différente des illustrations, mais les instructions d'installation demeurent les mêmes. Mise en garde Ne branchez l'unité tactile qu'aux modèles BrightLink 595Wi/595Wi+ ou BrightLink Pro 1430Wi. Ne branchez pas l'unité tactile à d'autres projecteurs ou appareils. A Mettez - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 124
2. Sélectionnez Config. uni. tactile. 3. Sélectionnez Motif d'installation. Le motif d'installation s'affiche sur l'image projetée. C Retirez les marqueurs 1. Desserrez la vis dans la partie inférieure du couvercle des cadrans. 124 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 125
pour effectuer l'ajustement de l'angle (p. 127) après avoir installé l'unité tactile. D Déterminez la position d'installation de l'unité tactile Veuillez marquer les positions d'installation suivantes : • ( ) : Ligne centrale du motif d'installation. Alignez-la avec la ligne centrale de l'unit - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 126
é tactile • Pour les écrans magnétiques, placez l'arrière de l'unité tactile sur la surface de l'écran, puis fixez-la. Mise en garde Lors de l'installation de l'unité tactile sur une surface magnétique, veillez à ne pas coincer vos doigts ou toute autre partie de votre corps entre les aimants et - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 127
du ou des crayons interactifs est terminé. Appuyez sur le bouton User de la télécommande et sélectionnez Oui afin d'effectuer un calibrage automatique. Veuillez consulter le Guide de l'utilisateur pour obtenir des instructions détaillées sur le calibrage des crayons. 1. Sélectionnez Easy Interactive - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 128
2. Sélectionnez Config. uni. tactile. 3. Sélectionnez Alimentation et réglez le paramètre à On. L'unité tactile s'allume et le témoin indicateur s'allume en bleu. Témoin indicateur Avertissement Ne regardez pas la fenêtre de projection du projecteur ou les ports de diffusion laser de l'unité tactile - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 129
Français 4. Sélectionnez Réglage de l'angle. L'écran de réglage de l'angle s'affiche. 5. Tournez les cadrans de réglage de l'unité tactile dans le sens inverse des aiguilles d'une montre jusqu'à ce que vous entendiez un clic. Puis, appuyez sur le bouton de la télécommande. Lorsque vous ajustez les - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 130
6. Placez les deux marqueurs que vous avez retirés de l'unité tactile sur les positions des marqueurs ( ) ( ) sur l'écran de projection. Position du marqueur bleu Position du marqueur vert Faites correspondre les positions de sorte que les croix ( ) soient superposées avec les points ( ) sur les - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 131
Français Ne placez rien d'autre que les marqueurs à proximité de l'image projetée lors du réglage de l'angle. Si d'autres objets se trouvent sur l'image projetée, le réglage de l'angle pourrait ne pas être effectué correctement. 7. Tournez les cadrans d'ajustement de l'unité tactile pour déplacer - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 132
8. Lorsque les couleurs des pointeurs à gauche et à droite deviennent unies ( ) ( ), appuyez sur le bouton de la télécommande. L'écran suivant s'affiche : 9. Placez les marqueurs sur les positions de marqueur supérieures [1]. Si le réglage de l'angle a été effectué correctement, les couleurs des - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 133
Français 11. Lorsque vous avez terminé la vérification des positions des marqueurs, retirez les marqueurs et appuyez sur le bouton de la télécommande. L'écran de confirmation suivant s'affiche : 12. Tracez les points avec votre doigt tel qu'illustré. Si le réglage de l'angle est effectué - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 134
de la télécommande et effectuez à nouveau l'étape 12. Si les points ne disparaissent toujours pas après avoir effectué les procédures ci-dessus, communiquez avec Epson. 134 - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 135
Config. uni. tactile. Sélectionnez Calibrage tactile et suivez les instructions. H Stockez les marqueurs et posez les étiquettes 1. Stockez déplace hors position, utilisez la position des étiquettes pour déterminer où réinstaller l'unité tactile. I Posez le couvercle Fixez le couvercle des cadrans. - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 136
le boîtier de commande. Suivez les étapes ci-dessous pour installer le boîtier de commande et le connecter au projecteur. Avertissement Le boîtier de commande doit seulement être connecté aux projecteurs BrightLink Pro 1410Wi/ 1420Wi/1430Wi. Ne connectez pas le boîtier de commande à d'autres modèles - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 137
Français A Retirez le cache-câbles B Fixez le boîtier de commande Fixez le boîtier de commande avec des vis M4 x 20 mm (x4) disponibles dans le commerce. Avertissement ❏ Assurez-vous que les vis ne sont pas en angle. ❏ Assurez-vous que le boîtier de commande est solidement fixé. ❏ Ne fixez pas le - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 138
de commande afin d'éviter qu'il puisse glisser. C Installez les piles Mise en garde Avant de manipuler les piles, lisez les instructions de sécurité dans le Guide de l'utilisateur de votre projecteur. ❏ Utilisez deux piles au manganèse ou alcalines (recommandé). N'utilisez pas d'autres types de pile - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 139
Français D Connectez les câbles du projecteur au boîtier de commande Câble USB 1 Câble de la télécommande Câble USB 2 Câble USB 4 Câble USB 3 Clé UBS Pour effectuer les fonctions ci-dessous, vous devez brancher les câbles appropriés : Fonction du projecteur Câbles requis Projeter des - Epson 585W | Installation Guide - Ultra-Short Throw Wall Mount (ELPMB43) - Page 140
projecteur BrightLink. Pour obtenir plus de détails, consultez le Guide de l'utilisateur en ligne ou sur l'un des sites Web suivants : É.-U. : epson.com/support/brightlinkdownloads Canada : epson.ca/support/brightlinkdownloads Fixation d'un câble de sécurité Si le projecteur doit être installé dans
Installation Guide
Guide d’installation