Epson 8300NL Quick Start - Page 2

here to get help, roubleshooting - manual

Page 2 highlights

Quick Setup EPSON® PowerLite® 8300i Using the remote control You can use the remote control in place of your computer's mouse. This lets you control your computer and give slideshow-style presentations from anywhere in the room. 1 Connect the USB cable from your laptop to the projector. 2 If necessary, set up your laptop to work with a USB mouse. 3 If this is your first time using the remote, make sure its batteries are installed. Then turn on the power switch on the side of the remote. Troubleshooting If you see a blank screen... If you see a blank screen or the No signal message after turning on your laptop, check the following: Make sure the power light on the projector is green and not flashing, and the lens cover is off. No signal ( ? Help) Press the Computer/DVI button on the projector to select Computer 1 as the image source. If you're using a Windows laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labelled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it. Allow a few seconds for the projector to sync up after changing the setting. If the projector and laptop don't display the same image... Now you can use the remote control in place of your computer's mouse: Move cursor E-Zoom Page Power CMoloodr e A/V Mute R/C ON OFF Resize Freeze Left-click Menu Source Help Right-click You can also use the Page up and down buttons to change slides in PowerPoint. E-Zoom Page Power Change slides in PowerPoint CMoloodr e A/V Mute R/C ON OFF Resize Preview Preset Auto Focus Zoom LensShift Volume Num Freeze For more information on using the remote control, see your User's Guide. Where to get help Telephone Support Services To use the EPSON PrivateLine® Support service, call (800) 637-7661 and enter the PIN on the EPSON PrivateLine Support card included in your Start Here kit. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of these numbers: U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday Toll or long distance charges may apply. Electronic Support Services EPSON provides technical assistance through electronic support services 24 hours a day at http://support.epson.com. For tips, templates, and training for developing successful presentations go to http://www.presentersonline.com. If your image displays either on the projector or laptop, but not on both, check the following: Windows Try using the CRT/LCD or function key as described above. On most systems, this key lets you toggle between the LCD screen and the projector, or display on both at the same time. If that doesn't work, check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Windows Control Panel, open the Display utility. In the Display Properties dialog box, click the Settings tab, then click Advanced. The method for adjusting the setting varies; you may have to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled. See your laptop's manual or online help for details. Macintosh OS X 1. From the Apple menu, select System Preferences, then select Displays. 2. Select the Color LCD dialog box. Click here 3. Click the Arrange (or Arrangement) tab and click Mirror Displays. Macintosh OS 9.x or earlier 1. From the Apple menu, select Control Panels, then click Monitors or Monitors and Sound. Click here 2. Click the Arrange icon. Drag one monitor icon on top of the other 3. Drag one monitor icon on top of the other. If the Arrange option isn't available, click the Monitor icon and select a Simulscan resolution. EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite and PrivateLine are registered trademarks of Epson America, Inc. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. Copyright © 2003 by Epson America, Inc. Printed in XXX. 3/03 CPD-16108

  • 1
  • 2

You can use the remote control in place of your computer’s mouse.
This lets you control your computer and give slideshow-style
presentations from anywhere in the room.
1
Connect the USB cable from your
laptop to the projector.
2
If necessary, set up your laptop to work
with a USB mouse.
3
If this is your first time using the remote, make sure
its batteries are installed. Then turn on the power
switch on the side of the remote.
±
Now you can use the remote control in place
of your computer’s mouse:
±
You can also use the
Page
up
and down
buttons to change slides in PowerPoint.
For more information on using the remote control, see your
User’s Guide
.
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
EPSON disclaims any and all rights in those marks. Copyright © 2003 by Epson America, Inc.
Printed in XXX. 3/03
Quick Setup
EPSON
®
PowerLite
®
8300i
CPD-16108
U
sing the remote control
W
here to get help
Telephone Support Services
To use the EPSON PrivateLine
®
Support service, call (800) 637-7661
and enter the PIN on the EPSON PrivateLine Support card included in
your
Start Here
kit. This service is available 6
AM
to 6
PM
, Pacific Time,
Monday through Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing
one of these numbers:
U.S.
:
(562) 276-4394, 6
AM
to 6
PM
, Pacific Time,
Monday through Friday
Canada
:
(905) 709-3839, 6
AM
to 6
PM
, Pacific Time,
Monday through Friday
Toll or long distance charges may apply.
Electronic Support Services
EPSON provides technical assistance through electronic support
services 24 hours a day at http://support.epson.com. For tips,
templates, and training for developing successful presentations
A/V Mute
Help
Menu
Source
Preview
Preset
Volume
Num
Auto
Focus
Zoom
LensShift
Color
Mode
Resize
Freeze
Page
Power
E-Zoom
R/C
ON
OFF
Left-click
Right-click
Move
cursor
A/V Mute
Color
Mode
Resize
Freeze
Page
Power
E-Zoom
R/C
ON
OFF
Change slides in
PowerPoint
If you see a blank screen...
If you see a blank screen or the
No signal
message
after turning on your laptop, check the following:
±
Make sure the
power light on the projector
is green and not flashing, and the lens cover
is off.
±
Press the
Computer/DVI
button on the projector
to select
Computer 1
as the image source.
±
If you’re using a Windows laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be
labelled
CRT/LCD
or have an icon such as
. You may have to
hold down the
Fn
key while pressing it. Allow a few seconds for
the projector to sync up after changing the setting.
If the projector and laptop
don’t display the same image...
If your image displays either on the projector or laptop, but not on both,
check the following:
Windows
Try using the
CRT/LCD
or
function key as described above. On most
systems, this key lets you toggle between the LCD screen and the projector,
or display on both at the same time.
If that doesn’t work, check your monitor settings to make sure both the
LCD screen and the external monitor port are enabled. From the Windows
Control Panel, open the
Display
utility. In the Display Properties dialog box,
click the
Settings
tab, then click
Advanced
. The method for adjusting the
setting varies; you may have to click a
Monitor
tab, then make sure the
external Monitor port is set as your primary display and/or enabled.
See your laptop’s manual or online help for details.
Macintosh OS X
1.
From the Apple menu, select
System
Preferences
, then select
Displays
.
2.
Select the
Color LCD
dialog box.
3.
Click the
Arrange
(or
Arrangement
) tab
and click
Mirror Displays
.
Macintosh OS 9.x or earlier
1.
From the Apple menu, select
Control
Panels
, then click
Monitors
or
Monitors and Sound
.
2.
Click the
Arrange
icon.
3.
Drag one monitor icon on top of the other.
If the
Arrange
option isn’t available, click the
Monitor
icon and select a
Simulscan
resolution.
No signal (
?
Help)
Click here
Drag one monitor
icon on top of
the other
Click here
T
roubleshooting