Epson 875DC Product Information Guide - Page 4
Environmental, Safety Approvals, Control Panel, Installing an Ink Cartridge for the First Time - remove print head
View all Epson 875DC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
EPSON Stylus Photo 875DC Environmental Temperature Operation 50 to 95 °F (10 to 35 °C) Storage* −4 to 140 °F (−20 to 60 °C) 1 month at 140 °F (60 °C) Transit* -4 to 140 °F (-20 to 60 °C) 120 hours at 140 °F (60 °C) Humidity (without condensation) Operation 20 to 80% relative humidity Storage* 5 to 80% relative humidity *Stored in shipping container Safety Approvals Safety standards UL 1950, CSA C22.2 No. 950 EMC FCC part 15 subpart B class B Control Panel paper out light color ink out light black ink out light power light cleaning load/eject button button power button Follow these guidelines when you check the control panel lights. P is on S flashes and B and A are on The Ppower light is on when the printer is ready to print. It flashes when the printer is receiving a print job, charging ink, or cleaning the print head. When the S paper out light flashes and both ink out lights come on, you have a paper jam. Press the E load/eject button to try to clear the jam. If that doesn't work, turn off the printer and gently pull out all the paper. Make sure none of the sheets are curled, creased, old, stuck together, or too thin. Then reload the paper against the right edge guide and slide the left edge guide against it. Turn on the printer and press the E load/eject button to resume printing. S is on B or A flash B or A are on P and S flash and B and A are on P S B A flash P S B A are off When the S paper out light comes on, your paper is out or incorrectly loaded. Make sure none of the sheets are curled, creased, old, stuck together, or too thin. Then reload the paper against the right edge guide and slide the left edge guide against it. Press the E load/eject button to resume printing. When an ink out light flashes, your ink supply is low. Make sure you have a replacement cartridge. When an ink out light comes on, you need to replace the ink cartridge. Make sure you have a replacement cartridge. See page 9 for instructions. If an ink out light comes on after you've replaced a cartridge, you installed a cartridge your printer can't use. Remove it and replace it with the correct type (see page 4 for ink cartridge specifications). When the P power and S paper out lights flash and one or both of the ink out lights come on, jammed paper may be blocking movement of the print head. Turn off the printer, open the cover, and check inside for any jammed paper. Then turn the printer back on. If the lights still flash and/or come on, contact your dealer or EPSON. When all the lights flash, your printer may have an internal error. Make sure you removed all the packing material as described on the unpacking sheet in your printer box. Then turn off the printer, wait a few seconds, and turn it on again. If the lights still flash, contact your dealer or EPSON. When all the lights are off, the printer is not receiving power. Try these solutions: t Make sure the printer is turned on. t Turn off the printer, plug in the power cord securely, and turn on the printer again. t Make sure the outlet is operable and is not controlled by a switch or timer. If in doubt, try using another outlet. Installing an Ink Cartridge for the First Time Follow these ink cartridge precautions and the others on pages 7 through 8 of the Printer Basics book: t Install both ink cartridges, and leave them installed for all types of printing, or the printer won't work. t Remove the yellow tape seal from the top of the ink cartridges or you'll permanently damage them. Don't remove the clear seals on the bottom or ink will leak out. t Don't touch the green chip on the back of the cartridge. This may inhibit normal operation and printing. t Never turn off the printer when the P power light is flashing, unless the printer hasn't moved or made any noise for more than five minutes. 5 - EPSON Stylus Photo 875DC 4/00