Epson C11C417001 Product Information Guide - Page 4
Parallel Interface, USB Interface, Control Panel
![]() |
View all Epson C11C417001 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
EPSON Stylus Photo 820 Printable area A B-L single sheets or cards B-R No Margins ** C A B-L B-R C envelopes A: The minimum top margin is 0.12 inch (3.0 mm). When loading multiple sheets of EPSON Photo Quality Glossy Film, the minimum top margin is 1.2 inches (30.0 mm). B-L: The minimum left margin is 0.12 inch (3.0 mm). B-R: The minimum right margin is 0.28 inch (7.0 mm) for DL envelopes 1.10 inches (28.0 mm) for No. 10 envelopes 0.12 inch (3.0 mm) C6 envelopes and all other paper sheets C: The minimum bottom margin is 0.55 inch (14.0 mm). * You can extend the minimum bottom margin to 0.12 inch (3.0 mm) by selecting Maximum as the Printable Area setting. However, print quality may decline in the expanded area. ** When printing with No Margins, print quality may decline in the top and bottom areas of the printout or the area may be smeared. Parallel Interface Forward channel Specification Description Data format 8-bit parallel, IEEE-1284 compatibility mode Synchronization STROBE pulse Handshake timing BUSY and ACKNLG signals Signal level TTL compatible Connector 57-30360 Amphenol connector or equivalent Reverse channel Specification Description Transmission mode IEEE-1284 Nibble mode Adaptable connector 57-30360 Amphenol connector or equivalent Synchronization Refer to the IEEE-1284 specification Handshaking Refer to the IEEE-1284 specification Signal level IEEE-1284 Level 1 device Data transmission timing Refer to the IEEE-1284 specification USB Interface Specification Description Standard Based on Universal Serial Bus Specifications Revision 1.0, Universal Serial Bus Device Class Definition for Printing Devices Version 1.0 Bit rate 12 Mbps (full speed device) Data encoding NRZI Adaptable connector USB Series B Recommended cable length 6.5 feet (2 meters) maximum Control Panel To diagnose some problems, check the printer's control panel, as described below, or run a printer check (page 5). Lights Explanation P power light The printer is receiving a print job, replacing an ink flashes cartridge, charging ink, or cleaning the print head. P power light flashes and b error light is on b error light flashes Your paper ran out, ink ran out, or paper is jammed. You may also see a message on your screen. ❏ If paper is out, load more paper, then press the b maintenance button to resume printing. b ❏ If paper is jammed, press the maintenance button to eject the paper. If that doesn't work, turn off the printer, open the cover, and remove all the paper, including any torn pieces. Then turn on the printer, reload paper, and press the b maintenance button. ❏ If you see an ink out message on your screen, you need to replace one of your ink cartridges. See page 6 for details. One of the ink cartridges is low. Make sure you have a replacement cartridge. To determine which cartridge is low, check the ink level as described on page 6. P power light flashes and b error light is on Paper may be blocking movement of the print head. Turn off the printer, open the cover, and remove any jammed paper or other foreign objects. Then turn the printer on again. If the lights are still on, contact your dealer or EPSON. P power light and b error light flash alternately The printer may have an internal error. Turn off the printer, wait a few seconds, and turn it on again. If the lights are still flashing, contact your dealer or EPSON. Green P power light and red b error light are still on after replacing an ink cartridge One of your ink cartridges is installed incorrectly. Follow the steps on page 7 to remove your ink cartridges and then reinsert them. 4 - EPSON Stylus Photo 820 9/01
![](/manual_guide/products/epson-c11c417001-product-information-guide-f4ff8ae/4.png)