Epson FX-850 Product Information Guide - Page 2

Acknl - printer

Get Epson FX-850 - Impact Printer PDF manuals and user guides View all Epson FX-850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

FX - 850/1050 DOT - MATRIX PRINTER Humidity: Operation: 10% to 80% (without condensation) Storage: 5% to 85% (without condensation) Shock: Operation: Up to 1 G within 1 ms Storage: Up to 2 G within 7 ms Vibration: Operation: Up to 0.25 G at up to 55 Hz I Storage: up to 0.50 G at up to 55 Hz SelecType 1 I You can use the SelecType control panel to choose fonts, pitches, and condensed printing. The settings you select using the SelecType panel remain valid even after the printer is turned off. reset, or initialized. However, commands from your software application program temporarily override the SelecType settings. Character fonts The FX-850 and FX-1050 have three built-in character fonts: Epson Extended Graphics Character Table ROMAN !"P 0123456789:;?@ABCDEFGHIJK UlNOPQRSTUVWXYZC\l^-'abcdefghijklmnopqrstuv wxyzt: t- We've just seen your excellent ad for miniature zebras in a recent back issue of Trader Times. What is the price of these items for quantities of more than one gross? SANS SERIF !"#~~%&'0~+,-./012345t789:;~~~BCDEFG~IJK LMNOPORSTUVWXVZ[\]-_' a b c d e f g h i j k l m n o p q r s t u v w x y z c : >' We've just Seen your excellent ad for miniature zebras in a recent back issue of What is the price of these items far quantities of more than one gross? Interface timing The figure below shows the timing for the parallel interface. ACKLNWLSYc 4 i,+-& L Italic Character Table Default Settings The table below shows the default conditions that become valid when the printer is initialized. Initialization There are three ways that the printer can be initialized (returned to a fixed set of conditions). Hardware initialization l When the power is turned on Software initialization l When the printer receives an INIT signal at the parallel interface (pin 31 goes LOW). l Software sends the ESC @ (initialize the printer) command. FX - 850/1050 - 2 12/12/88 In addition, the data buffer is cleared when the printer is initialized by turning on the power or by an INIT signal. Note: The user-defined character set is not cleared when the printer is initialized. 9 - Pin Printers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
FX - 850/1050 DOT - MATRIX PRINTER
Humidity:
Operation: 10% to 80% (without
condensation)
Shock:
Vibration:
Storage: 5% to 85% (without condensation)
Operation: Up to 1 G within 1 ms
Storage: Up to
2
G within 7 ms
Operation: Up to 0.25 G at up to
55 Hz
I
Storage: up to 0.50 G at up to 55 Hz
SelecType
1
I
You can use the SelecType control panel to choose fonts, pitches, and
condensed printing. The settings you select using the SelecType panel
remain valid even after the printer is turned off. reset, or initialized.
However, commands from your software application program
temporarily override the SelecType settings.
Character fonts
The FX-850 and FX-1050 have three built-in character fonts:
ROMAN
!“P#$%&‘()*+,-./0123456789:;<=>?@ABCDEFGHIJK
UlNOPQRSTUVWXYZC\l^-‘abcdefghijklmnopqrstuv
wxyzt:
t-
We've just seen your excellent ad for
miniature zebras in a recent back issue of
Trader Times. What is the price of these
items for quantities of more than one gross?
SANS SERIF
!“#~~%&‘0~+,-./012345t789:;<=>~~~BCDEFG~IJK
LMNOPORSTUVWXVZ[\]-_‘
abcdefghijklmnopqrstuv
wxyzc:
>’
We’ve
just
Seen your excellent ad for
miniature zebras in a recent back issue of
What is the price of these
items far quantities of more than one
gross?
Interface
timing
The figure below shows the timing for the parallel interface.
LWSY
4
ACKNL
c
i,
+-&
Initialization
There are three ways that the printer can be initialized (returned to a
fixed set of conditions).
Hardware
initialization
l
When the power is turned on
l
When the printer receives an INIT signal at
the parallel interface (pin 31 goes LOW).
Software initialization
l
Software sends the ESC @ (initialize the
printer)
command.
FX - 850/1050 - 2
12/12/88
Epson Extended
Graphics Character Table
L
Italic Character Table
Default Settings
The table below shows the default conditions that become valid when
the printer is initialized.
In addition, the data buffer is cleared when the printer is initialized by
turning on the power or by an INIT signal.
Note: The user-defined character set is not cleared
when
the
printer is
initialized.
9 - Pin Printers