Epson M-Tracer MT500GII Start Here - Page 4

Using the Product

Get Epson M-Tracer MT500GII PDF manuals and user guides View all Epson M-Tracer MT500GII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

3 Slide the product onto the attachment until it comes in contact with the stoppers at the end. Stopper NOTE • D o not push too hard when the attachment is tight on the grip of the golf club. Try a thinner grip area or a larger attachment. • If the attachment is too loose, try a thicker grip area or a smaller attachment. 4 Make sure the product is firmly attached to the grip. Caution The product should not move when attached to the grip. Doesn't move back and forth Doesn't move around • Make sure the product is attached to the underside of the club. • If the product is scratched while mounting, it should not affect its functioning. 6. Using the Product 1 Hold down the power button on the product for at least two seconds to turn it on. The blue status LED flashes once every two seconds. 2 Connect the product to your mobile device using Bluetooth. 3 Tap on your mobile device.  While your mobile device and product are communicating, the blue LED flashes. 4 Tap Measure to start. The red status LED turns on. If you need to choose the type of club or shot, tap Stop, then tap Setup. To start measuring again, tap Start. 5 Address the ball. When the product detects that you are standing still (this takes a few seconds), the blue status LED turns on. Target line 90° Shaft 90° Club face 6 Swing the club. After detecting the impact of the swing, the blue LED flashes and the data is transmitted to your mobile device. The product will not measure your swing if the impact is not detected. Repeat steps 5 and 6 to record multiple swings. 7 When you are finished swinging, tap Stop. 8 Go to the Analysis page: Tap Analysis on iOS. Tap Back on Android. 9 Push the power button on the product for 2 seconds to turn it off. The product automatically turns off when your mobile device screen is left on any screen other than the Measurement screen for over 10 minutes.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
3
Slide the product onto the attachment until it comes in contact with the
stoppers at the end.
Stopper
NOTE
• Do not push too hard when the attachment is tight on the grip of the golf club.
Try a thinner grip area or a larger attachment.
• If the attachment is too loose, try a thicker grip area or a smaller attachment.
4
Make sure the product is firmly attached to the grip.
Doesn’t move
back and forth
Doesn’t move
around
Caution
The product should not move
when attached to the grip.
• Make sure the product is attached to the underside of the club.
• If the product is scratched while mounting, it should not affect its functioning.
6. Using the Product
1
Hold down the power button on the product for at least two seconds to turn it
on.
The blue status LED flashes once every two seconds.
2
Connect the product to your mobile device using Bluetooth.
3
Tap
on your mobile device.
While your mobile device and product are communicating, the blue LED
flashes.
4
Tap
Measure
to start.
The red status LED turns on.
If you need to choose the type of club or shot, tap
Stop
, then tap
Setup
.
To start measuring again, tap
Start
.
5
Address the ball.
When the product detects that you are standing still (this takes a few seconds),
the blue status LED turns on.
Shaft
Club face
Target line
90°
90°
6
Swing the club.
After detecting the impact of the swing, the blue LED flashes and the data is
transmitted to your mobile device. The product will not measure your swing if
the impact is not detected.
Repeat steps 5 and 6 to record multiple swings.
7
When you are finished swinging, tap
Stop
.
8
Go to the Analysis page:
Tap
Analysis
on iOS.
Tap
Back
on Android.
9
Push the power button on the product for 2 seconds to turn it off.
The product automatically turns off when your mobile device screen is left on
any screen other than the Measurement screen for over 10 minutes.