Epson PowerLite 1955 Quick Setup - Page 3

Project over a wired network

Get Epson PowerLite 1955 PDF manuals and user guides View all Epson PowerLite 1955 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

4 Replace the wireless LAN module stopper and secure it using the screw you removed. 5 Close the air filter cover. 6 To configure your projector for your wireless network, do one of the following: • If you're using the optional Quick Wireless Connection USB key, insert it into the projector's USB-A port, look for the displayed message, remove the key, and connect it to a USB port on your computer. Follow the on-screen instructions to install the driver, then run your presentation. For details, see the online User's Guide. • If you're not using the key, continue with the steps bbelow. 7 Press the Menu button on the remote control, select the Network menu, and press . Project over a wired network Follow the steps here to configure your projector for your wired network using the projector's menu system. 1 Plug in and turn on the projector. 2 Press the Menu button on the remote control, select the Network menu, and press . 3 Select Network Configuration and press . 4 Select the Basic menu and press . 8 Choose Network Configuration and press . 9 Select the Wireless LAN menu and press . 5 Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network. Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press to select them. Note: See the online User's Guide for information on adding passwords. 6 Select the Wired LAN menu and press . 10 Click Quick or Advanced, and enter your network's SSID. 11 If your network assigns addresses automatically turn on DHCP. If not, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address, as needed. To enter numbers, use the arrow buttons on the remote control to highlight a number, then press the button. When you're finished entering an address, highlight Return, then press . 12 To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and/or IP Address Display settings to Off. 13 See "Install network software" for additional instructions. 7 Choose IP Settings and press . 8 If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector's IP Address, Subnet Mask, and Gateway Address, as needed. 9 To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off. 10 When you are finished, select Complete and press again to save your settings. , then press 11 Press the Menu button to exit the menu system. 12 See "Install network software" for additional instructions.

  • 1
  • 2
  • 3
  • 4
4
Replace the wireless LAN module stopper and secure it using the screw
you removed.
5
Close the air filter cover.
6
To configure your projector for your wireless network, do one of the
following:
•
If you’re using the optional Quick Wireless Connection USB key, insert
it into the projector’s
USB-A
port, look for the displayed message,
remove the key, and connect it to a USB port on your computer.
Follow the on-screen instructions to install the driver, then run your
presentation. For details, see the online
User’s Guide
.
•
If you’re not using the key, continue with the steps bbelow.
7
Press the
Menu
button on the remote control, select the
Network
menu,
and press
.
8
Choose
Network Configuration
and press
.
9
Select the
Wireless LAN
menu and press
.
10
Click
Quick
or
Advanced
, and enter your network’s
SSID
.
11
If your network assigns addresses automatically turn on
DHCP
. If not,
turn off
DHCP
and enter the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the
button. When you’re finished
entering an address, highlight
Return
, then press
.
12
To prevent the SSID and IP address from appearing on the network
standby screen, set the
SSID Display
and/or
IP Address Display
settings to
Off
.
13
See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the
Menu
button on the remote control, select the
Network
menu,
and press
.
3
Select
Network Configuration
and press
.
4
Select the
Basic
menu and press
.
5
Select the
Projector Name
setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press
to select
them.
Note:
See the online
User’s Guide
for information on adding passwords.
6
Select the
Wired LAN
menu and press
.
7
Choose
IP Settings
and press
.
8
If your network assigns addresses automatically, select
IP Settings
and
turn on the
DHCP
setting. If not, turn off the
DHCP
setting and enter
the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
,
as needed.
9
To prevent the IP address from appearing on the network standby screen,
set the
IP Address Display
setting to
Off
.
10
When you are finished, select
Complete
and press
, then press
again to save your settings.
11
Press the
Menu
button to exit the menu system.
12
See “Install network software” for additional instructions.