Epson PowerLite Home Cinema 5025UB Quick Start and Warranty - Page 2

Adjust the image, Using the remote control, Viewing 3D images

Get Epson PowerLite Home Cinema 5025UB PDF manuals and user guides View all Epson PowerLite Home Cinema 5025UB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Adjust the image 1 If you don't see an image, press one of the Source buttons on the remote control or the button on the projector to select the image source. Note: If you still see a blank screen or have other display problems, see "Troubleshooting." 2 Turn the horizontal and vertical lens shift dials to adjust the image position and center it on the screen. Using the remote control Make sure the batteries are installed as shown (two AA batteries). 3 To raise the image, adjust the front feet as shown below. 4 Turn the zoom ring to reduce or enlarge the image. Turn projector on Choose which source to display Switch between 2D and 3D Access projector menus Turn projector off Turn off projector display Navigate projector menus 5 Turn the focus ring to sharpen the image. 6 If your image looks like or the projector to correct this. , you can press the or buttons on For more information on using the remote control, see the online User's Guide. Viewing 3D images To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. You also need a pair of Epson® (part number V12H548006) or Epson-compatible RF 3D active shutter glasses. 1 Turn on and begin playback on the 3D-compatible video device. Note: Make sure you set the video device to play content in 3D mode. 2 Press the 2D/3D button on the remote control, if necessary. 3 Slide the power switch on your 3D glasses to the On position. Note: When setting up the projector, make sure that it is placed level to the screen in order to provide the best possible image quality. If you must set up the projector at an angle, use the or buttons to correct the image shape. Note: If the glasses don't automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds. The status light on the glasses will alternately flash green and red, then remain green for 10 seconds if pairing is successful.

  • 1
  • 2
  • 3
  • 4
Adjust the image
1
If you don’t see an image, press one of the Source buttons on the remote
control or the
button on the projector to select the image source.
Note:
If you still see a blank screen or have other display problems,
see “Troubleshooting.”
2
Turn the horizontal and vertical lens shift dials to adjust the image
position and center it on the screen.
3
To raise the image, adjust the front feet as shown below.
4
Turn the zoom ring to reduce or enlarge the image.
5
Turn the focus ring to sharpen the image.
6
If your image looks like
or
, you can press the
or
buttons on
the projector to correct this.
Note:
When setting up the projector, make sure that it is placed level
to the screen in order to provide the best possible image quality. If you
must set up the projector at an angle, use the
or
buttons to correct the
image shape.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which source
to display
Turn projector on
Access projector menus
Turn off projector
display
Navigate projector
menus
Turn projector off
Switch between
2D and 3D
For more information on using the remote control, see the online
User’s
Guide
.
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the
HDMI
ports on your projector. You also need a pair of Epson
®
(part
number V12H548006) or Epson-compatible RF 3D active shutter glasses.
1
Turn on and begin playback on the 3D-compatible video device.
Note:
Make sure you set the video device to play content in 3D mode.
2
Press the
2D/3D
button on the remote control, if necessary.
3
Slide the power switch on your 3D glasses to the
On
position.
Note:
If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the
Pairing
button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.