Esoteric D-05X Owners Manual EN FR SP - Page 19

Troubleshooting - review

Get Esoteric D-05X PDF manuals and user guides View all Esoteric D-05X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

English Troubleshooting If you experience a problem with this unit, please take a moment to review the following information before requesting service. Moreover, the problem might be caused by something other than this unit. Please also check the operation of the connected units. If this product still does not operate correctly, contact the retailer where you purchased it. The CLOCK indicator does not stop blinking. ee Set CLK> to OFF when not using clock sync (page 15). ee A clock signal to which the unit cannot synchronize might be being input. Check the connection of the CLOCK SYNC IN connector and the settings of the connected device. The unit does not turn on. ee Confirm that the power cord is securely connected to both the inlet on the back of this unit and a power outlet. ee Confirm that power is being supplied to the outlet to which the power cord is connected by, for example, connecting another device to it. This unit uses a microprocessor, so noise and other external interference could cause it to stop functioning properly. In such a case, turn the unit off and wait about one minute before restarting operation from the beginning. No sound is output from the speakers. The sound is distorted. ee Turn the power off and check the connections with the digital audio source device, the amp and the speakers (pages 7 and 8). ee Change the input setting to the connector that is being used for input (page 12). ee Change the output setting to match the connectors being used to connect the amplifier (page 12). ee Adjust the volume of the amplifier and other devices. No sampling frequency is shown to the right of the input on the display. ee Turn the device that is connected to the selected input connector on. ee Confirm that the device is properly connected to the selected input connector. ee When the input source is ESLINK, this shows the input signal format (PCM or DSD). A cyclical noise is being output. ee If a cyclical noise is being output when the unit is in clock sync mode, the connected device might not also be in clock sync mode. Check the connection of the CLOCK SYNC IN connector and the clock sync setting of the connected device. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
19
English
Troubleshooting
If you experience a problem with this unit, please take a moment
to review the following information before requesting service°
Moreover, the problem might be caused by something other than
this unit° Please also check the operation of the connected units°
If this product still does not operate correctly, contact the retailer
where you purchased it°
The unit does not turn on.
e
Confirm that the power cord is securely connected to both the
inlet on the back of this unit and a power outlet°
e
Confirm that power is being supplied to the outlet to which
the power cord is connected by, for example, connecting
another device to it°
No sound is output from the speakers. The sound is distorted.
e
Turn the power off and check the connections with the digital
audio source device, the amp and the speakers (pages 7
and 8)°
e
Change the input setting to the connector that is being used
for input (page 12)°
e
Change the output setting to match the connectors being
used to connect the amplifier (page 12)°
e
Adjust the volume of the amplifier and other devices°
No sampling frequency is shown to the right of the input on
the display.
e
Turn the device that is connected to the selected input con-
nector on°
e
Confirm that the device is properly connected to the selected
input connector°
e
When the input source is ESLINK, this shows the input signal
format (PCM or DSD)°
A cyclical noise is being output.
e
If a cyclical noise is being output when the unit is in clock sync
mode, the connected device might not also be in clock sync
mode° Check the connection of the CLOCK SYNC IN connector
and the clock sync setting of the connected device°
The CLOCK indicator does not stop blinking.
e
Set CLK> to OFF when not using clock sync (page 15)°
e
A clock signal to which the unit cannot synchronize might be
being input° Check the connection of the CLOCK SYNC IN con-
nector and the settings of the connected device°
This unit uses a microprocessor, so noise and other exter-
nal interference could cause it to stop functioning properly.
In such a case, turn the unit off and wait about one minute
before restarting operation from the beginning.