Fellowes 225Mi Manual - Page 4

Cleaning Auto-start Infrared Sensors, Oiling Shredder

Page 4 highlights

ENGLISH Model 225Mi PRODUCT MAINTENANCE CLEANING AUTO-START INFRARED SENSORS Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the sensors may become blocked by paper dust causing the motor to run even if there is no paper present. (Note: two paper detection sensors are located in the center of the paper entry). TO CLEAN THE SENSORS 1 2 3 225Mi 14 AUTO 4 225M i 14 Turn off and unplug shredder Locate Auto-start infrared sensor Dip cotton swab in rubbing alcohol Using cotton swab, wipe away any contamination from the paper sensors OILING SHREDDER All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin. FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE 1 2 225Mi AUTO14 AUTO *Apply oil across entry Press and hold forward ( ) 2-3 seconds *Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250 TPRROEVUEBNLETSIVHEOMOTAIINNGTENANCE & ACCESSORIES 15 Door Open Indicator: The shredder will not run if the cabinet door is open. When illuminated, close the door to resume shredding. Bin Full Indicator: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054. Remove Paper Indicator: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and reefed into paper entry. SafeSense® Indicator: If hands are too close to the paper entry, the SafeSense® indicator will illuminate and the shredder will stop shredding. If SafeSense® is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding. Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds. Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6

Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
CLEANING AUTO-START INFRARED SENSORS
PRODUCT MAINTENANCE
Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the sensors may become blocked by paper dust causing the motor to run
even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry)
.
TO CLEAN THE SENSORS
Turn off and unplug
shredder
Locate Auto-start
infrared sensor
Using cotton swab, wipe
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
ENGLISH
Model 225Mi
All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive
noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you
empty your waste bin.
OILING SHREDDER
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
TROUBLESHOOTING
Press and hold forward
(
) 2-3 seconds
AUTO
2
3
AUTO
1
2
4
1
Bin Full Indicator: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054.
Door Open Indicator: The shredder will not run if the cabinet door is open. When illuminated, close the door to resume shredding.
Remove Paper Indicator: When illuminated, press reverse (
) and remove paper. Reduce paper quantity to an acceptable amount and reefed into paper entry.
SafeSense
®
Indicator:
If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding.
If SafeSense
®
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds.