Fender Deluxe Reverb Solid State Owner Manual - Page 7

Control Operation

Get Fender Deluxe Reverb Solid State PDF manuals and user guides View all Fender Deluxe Reverb Solid State manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

CONTROL OPERATION 1. Insert cable from instrument or microphone into Amplifier front panel jacks, either Normal Channel marked 1 and 2 or Vibrato Channel marked 1 and 2. 2. Plug power cord from the Amplifier into a 117 VAC 60 Hz outlet. CAUTION: Before performing step 3 set Volume Controls on front panel at zero to prevent possible damae to speakers. 3. Turn the On-Off Switch, located on the back panel, to the "on" position. 4. Check to see that the pilot light on the front panel is lit. 5. Adjust Volume Controls to the desired level. 6. Change position of On-off-ground switch to eliminate undesirable noise and hum. Cover Care An occasional cleaning with a soft moist cloth should remove both fingerprints and dulling film from the Tolex cover. Power Consumption ZERO SIGNAL-10 -Watts Vibrolux/Reverb, 10-Watts Deluxe/Reverb MAXIMUM SIGNAL-140 -Watts Vibrolux/ Reverb, 100-Watts Deluxe/Reverb POWER REQUIREMENT-117 Volts-60 Hz. Speaker Fuse Extractor type fuse is easily accessible for replacement from the back panel, right hand side. Replace with 6 amp fast acting fuse only, (4 amp fast acting fuse- Pro/Reverb and Super/Reverb). If everything is normal but no sound is heard from the speakers, check the speaker protection fuse. SOLID STAT WWI

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
CONTROL OPERATION
1.
Insert
cable
from
instrument
or
microphone
into
Amplifier
front
panel
jacks,
either
Normal
Channel
marked
1
and
2
or
Vibrato
Channel
marked
1
and
2.
2.
Plug
power
cord
from
the
Amplifier
into
a
117
VAC
60
Hz
outlet.
CAUTION:
Before
performing
step
3
set
Volume
Controls
on
front
panel
at
zero
to
prevent
possible
damae
to
speakers.
3.
Turn
the
On
-Off
Switch,
located
on
the
back
panel,
to
the
"on"
position.
4.
Check
to
see
that
the
pilot
light
on
the
front
panel
is
lit.
5.
Adjust
Volume
Controls
to
the
desired
level.
6.
Change
position
of
On
-off
-ground
switch
to
eliminate
undesir-
able
noise
and
hum.
Cover
Care
An
occasional
cleaning
with
a
soft
moist
cloth
should
remove
both
fingerprints
and
dulling
film
from
the
Tolex
cover.
Power
Consumption
ZERO
SIGNAL
-10
-Watts
Vibrolux/Reverb,
10
-Watts
Deluxe/Reverb
MAXIMUM
SIGNAL
-140
-Watts
Vibrolux/
Reverb,
100
-Watts
De-
luxe/Reverb
POWER
REQUIREMENT
-117
Volts
-60
Hz.
Speaker
Fuse
Extractor
type
fuse
is
easily
accessible
for
replacement
from
the
back
panel,
right
hand
side.
Replace
with
6
amp
fast
acting
fuse
only,
(4
amp
fast
acting
fuse—
Pro/Reverb
and
Super/Reverb).
If
everything
is
normal
but
no
sound
is
heard
from
the
speakers,
check
the
speaker
protection
fuse.
WWI
SOLID
STAT