Fender Hot Rod Deluxe Owners Manual - Page 6

ENGLISH ENGLISH 6 Fender® Hot Rod™ Deluxe Your new Hot Rod™ Deluxe delivers world-class Fender® tone and world-standard Fender® quality. • 40 watts output into 4Ω or 8Ω • All tube preamp and power amp provide harmonically rich distortion and touch-sensitive dynamics • Three selectable channels offer a sonic arsenal from sparkling clean tones to virtually unlimited gain fueled by 12AX7 Fender® Groove Tubes™ • Output tubes are performance tested and matched GT6L6B Fender® Groove Tubes™ • Two-button footswitch (included) enables remote Normal/Drive/More Drive channel selection • PREAMP OUT / POWER AMP IN jacks for effects, amplifiers, recording or sound reinforcement setups • EXTERNAL SPEAKER jack offers flexibility of optional speaker array connections • Rugged cabinet construction and durable vinyl cover Thank you for choosing Fender® -Tone, Tradition and Innovation-since 1946 ESPAÑOL ESPAÑOL FRANçAIS FRANçAIS ITALIANO ITALIANO Panel Functions INPUTS 1 2 VOLUME 6 5 78 DRIVE 56 78 TREBLE 6 5 78 BASS 6 5 78 MIDDLE 6 5 78 MASTER 6 5 7 8 REVERB 6 5 78 PRESENCE PREAMP POWER FOOT 56 78 OUT AMP IN SWITCH 4 94 94 94 94 94 94 94 9 3 10 3 10 3 10 3 10 3 10 3 10 3 10 3 10 2 NORMAL 1 11 2 12 MORE 1 11 12 2 11 2 11 2 11 2 11 2 11 2 11 1 12 1 12 1 12 CHANNEL 1 12 1 12 1 12 BRIGHT DRIVE SELECT A BC D E F G H I J K L M N O P ON ON STANDBY OFF Q RS A. INPUT 1 - Plug in connection for most guitars. B. INPUT 2 - Plug in connection for high-output/ pre-amplified instruments. Provides 6dB less gain (sensitivity) than INPUT 1 if used alone - both inputs are identical if used simultaneously. C. NORMAL/BRIGHT - Provides a high-frequency boost for the Normal channel. Normal Bright D. VOLUME - Adjusts the loudness of the Normal channel. E. MORE DRIVE - Provides gain boost for the Drive channel. Drive More Drive N. PRESENCE - Adjusts the tone at a point in the signal path after the distortion circuitry for unique ultra highfrequency tone shaping. O. PRE AMP OUT / POWER AMP IN (1) Effects Loop - Connect PREAMP OUT to the input of an effects device and the output of the effects device to POWER AMP IN. (2) Multiple Hot Rod™ Amps - Connect PREAMP OUT on the primary unit to POWER AMP IN on the auxiliary unit. The primary unit is used to control all auxiliary units, except for REVERB and PRESENCE which remain active on each unit. (3) Recording or Sound Reinforcement - Connect PREAMP OUT to the input jack of sound equipment. F. DRIVE - Adjusts the gain level of the Drive/ More Drive channel. Use together with MASTER {L} to adjust the loudness of the Drive/ More Drive channel. G. CHANNEL INDICATOR - Off Normal channel is active Yellow Drive channel is active Red More Drive channel is active H. TREBLE - Adjusts the high-frequency tone. I. BASS - Adjusts the low-frequency tone. J. MIDDLE - Adjusts the mid-frequency tone. Use standard cables with TS (Tip-Sleeve) plugs for connections. Both jacks are before Reverb and Presence in the signal path. P. FOOTSWITCH (Included) - Connect the footswitch here to enable remote selection of Normal/Drive/More Drive channels. When connected, the footswitch overrides the corresponding panel controls. NOTE: A speaker grade patch cord is preferable to a coax guitar cord for connecting the footswitch. Q. POWER INDICATOR - Illuminates when the unit is on. Unscrew the red jeweled cover to access the bulb (type T47) for replacement. K. CHANNEL SELECT Normal channel Drive channel L. MASTER - Adjusts the loudness of the Drive/ More Drive channels in conjunction with DRIVE {F}. M. REVERB - Adjusts the Reverb level. R. STANDBY - Use STANDBY instead of switching the power off during short breaks to eliminate the tube warm-up delay upon returning to play. Use STANDBY for 30 seconds when first switching the power on. Using these standby procedures will extend the life span of your amplifier tubes. S. POWER SWITCH - Turns the unit on and off. www.f e n d e r.com ✧ www. m r g e a r h e a d .net DEUTSCH DEUTSCH