Fisher and Paykel DE62T27GW2 SmartLoad Clothes Dryer Installation Instructions - Page 27

plus separate grounding connector

Get Fisher and Paykel DE62T27GW2 PDF manuals and user guides View all Fisher and Paykel DE62T27GW2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3-Wire Connections plus separate grounding connector For use where local codes do not permit grounding through the Neutral wire. Use approved 3-wire Power Supply Cord or a 3-wire Cable for Direct Wiring as described on page 25. A separate 10AWG copper grounding wire is required. 1 Remove the terminal block cover plate. 2 Insert the power supply cable with a UL listed strain relief through the hole provided in the cabinet near the terminal block. Do not tighten strain relief screw until wiring connections are complete. Note: a strain relief must be used. 2 strain relief clamp sections strain relief screws 3 Remove center terminal block screw. 4 Remove appliance ground link by removing the ground connector screw (Green screw). 5 Connect a separate copper ground wire (green with yellow stripe) using the ground connector screw (Green screw). Make sure a ring terminal is used when connecting the ground wire and that the wire is firmly secured to an adequate grounding path. 3 7 Note: If the appliance is 6 4 moved back to a 3-wire 5 installation the ground link must be refitted. Remove link 7 6 Connect the neutral wire (center) of the power supply cord to the center terminal screw of the terminal block. Tighten screw. 7 Connect the other wires to the upper and lower terminal block screws marked with the letter L. Tighten screws. 8 Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer and secure cover with securing screw. 9 Tighten strain relief screws. 8 9 grounding wire It is recommended that a qualified electrician determine that the ground path is adequate 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
27
3-Wire Connections
plus separate grounding connector
For use where local codes
do not permit
grounding through the Neutral wire.
Use approved 3-wire Power Supply Cord or a 3-wire Cable for Direct Wiring as described on page 25.
A separate 10AWG copper grounding wire is required.
1
Remove the terminal block cover plate.
2
Insert the power supply cable with a UL listed strain relief through the hole provided in the cabinet
near the terminal block. Do not tighten strain relief screw until wiring connections are complete.
Note:
a strain relief must be used.
2
strain relief
clamp sections
strain relief
screws
3
Remove center terminal block screw.
4
Remove appliance ground link by removing the ground connector screw (Green screw).
5
Connect a separate copper ground wire (green with yellow stripe) using the ground connector
screw (Green screw). Make sure a ring terminal is used when connecting the ground wire and that
the wire is firmly secured to an adequate grounding path.
3
4
7
6
5
7
Note: If the appliance is
moved back to a 3-wire
installation the ground
link must be refitted.
Remove link
6
Connect the neutral wire (center) of the power supply cord to the center terminal screw of the
terminal block. Tighten screw.
7
Connect the other wires to the upper and lower terminal block screws marked with the
letter L. Tighten screws.
8
Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer and secure
cover with securing screw.
9
Tighten strain relief screws.
It is recommended that a qualified electrician
determine that the ground path is adequate
grounding wire
8
9