Fisher and Paykel RF170ADUX1 ActiveSmart™ Ice & Water User Guide - Page 13

Important

Get Fisher and Paykel RF170ADUX1 PDF manuals and user guides View all Fisher and Paykel RF170ADUX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installation instructions 11 Important! ■■ All connections must be checked for leaks. ■■ Ensure white 6 mm (¼") tubing is routed away from sharp objects, sharp corners (beware of kinking tube as this will stop water flow), clear of the refrigerator unit compartment and not in a location where it can be squashed. ■■ Ensure all push-fit connections are firmly pushed into place. The tube should push in 20 mm (¾") before reaching the stop. ■■ If tubing is removed at any point, re-cut the end and re-insert. Tubing must be fully inserted to avoid leaks. ■■ To remove tube from connection points, turn off the isolating tap, push in the collet and gently pull tubing at the same time. Diagram 9 Fig.9 Connection to water supply System tested and certified by NSF International against NSF/ANSI Standard 53 for the reduction of Asbestos, Atrazine, Benzene, Cyst, Carbofuran, Lead, Lindane, Mercury, P-Dichlorobenzene, Toxaphene & Turbidity; against Standard NSF/ANSI 42 for the reduction of Chlorine Taste and Odour and Nominal Particulate Class I to a capacity of 2,838 Litres (750 gallons).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
11
Installation instructions
Important!
■
±
All connections must be checked for leaks.
■
±
Ensure white 6 mm (¼”) tubing is routed away from sharp objects, sharp corners (beware of
kinking tube as this will stop water flow), clear of the refrigerator unit compartment and not in a
location where it can be squashed.
■
±
Ensure all push-fit connections are firmly pushed into place. The tube should push in 20 mm (¾”)
before reaching the stop.
■
±
If tubing is removed at any point, re-cut the end and re-insert. Tubing must be fully inserted to
avoid leaks.
■
±
To remove tube from connection points, turn off the isolating tap, push in the collet and gently
pull tubing at the same time.
Fig.9 Connection to water supply
Diagram 9
System tested and certified by NSF International against NSF/ANSI Standard 53 for the reduction
of Asbestos, Atrazine, Benzene, Cyst, Carbofuran, Lead, Lindane, Mercury, P-Dichlorobenzene,
Toxaphene & Turbidity; against Standard NSF/ANSI 42 for the reduction of Chlorine Taste and
Odour and Nominal Particulate Class I to a capacity of 2,838 Litres (750 gallons).