Foxconn A79A-S English Manual. - Page 39

► PCIE 16X Port 1/Port 2/Port 3/ Port 4, PCIE 1X Port 1, NB-SB Port Features

Get Foxconn A79A-S PDF manuals and user guides View all Foxconn A79A-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

3 PCI_E3_x16 slot and PCI_E4_x16 slot; Select [Disabled], the two slots can not be used for the CrossFireTM Technology. ► Peer-to-Peer among GFX/GFX2 This item is used to control the peer-to-peer traffic among GFX/GFX2 slots. The default value is [Disabled]. ► GPP Slots Power Limit, W This item is used to set the power limit for the graphic slots. You can use [+]/[-] to change the value or input a value directly from 0 to 255. The default value is 25. ► PCIE 16X Port 1/Port 2/Port 3/ Port 4, PCIE 1X Port 1, NB-SB Port Features Press [Enter] to go to its submenu. Memory Configuration CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Memory Configuration Memory Configuration Help Item Bank Interleaving [Aut o] Enable Bank Memory Channel Interleaving [XOR of Address bit] Interleaving Enable Clock to ALL DIMMs [Disabled] MemClk Tristate C3/ALTVID [Disabled] Memory Hole Remapping [Enabled] DCT Unganged Mode [Always] Power Down Enable [Disabled] Optimal Performance Mode [Disabled] Auto Tweak Performance [Disabled] DRAM Config_High Control [Auto] Move Enter:Select +/-/:Value F10:Save ESC:Exit F1:General Help F9:Optimized Defaults ► Bank Interleaving Interleaving allows banks of SDRAM to alternate their refresh and access cycles. One bank will undergo its refresh cycle while another is being accessed. This improves memory performance by masking the refresh cycles of each memory bank. However, bank interleaving only works if the addresses requested consecutively are not in the same bank. ► Channel Interleaving Dual channel (Interleaved) mode offers the highest throughput for real world applications. Dual channel mode is enabled when the installed memory capacities of both DIMM channels are equal. If different speed DIMMs are used between channels, the slowest memory timing will be used. ► Enable Clock to All DIMMs This setting is to control EMI. When disabled, the system will turn off clock on the empty DIMM slots and to reduce EMI (Electro-Magnetic Interference). ► MemClk Tristate C3/ALTVID Enables the DDR memory clocks to be tristated when alternate VID mode is enabled. ► Memory Hole Remapping 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
3
32
PCI_E3_x16 slot and PCI_E4_x16 slot; Select [Disabled], the two slots can not be used for the
CrossFire
TM
Technology.
► Peer-to-Peer among GFX/GFX2
This item is used to control the peer-to-peer traffic among GFX/GFX2 slots. The default value
is [Disabled].
► GPP Slots Power Limit, W
This item is used to set the power limit for the graphic slots. You can use [+]/[-] to change the
value or input a value directly from 0 to 255. The default value is 25.
► PCIE 16X Port 1/Port 2/Port 3/ Port 4, PCIE 1X Port 1, NB-SB Port Features
Press [Enter] to go to its submenu.
Memory Configuration
► Bank Interleaving
Interleaving allows banks of SDRAM to alternate their refresh and access cycles. One bank
will undergo its refresh cycle while another is being accessed. This improves memory perfor-
mance by masking the refresh cycles of each memory bank.
However, bank interleaving only works if the addresses requested consecutively are not in the
same bank.
► Channel Interleaving
Dual channel (Interleaved) mode offers the highest throughput for real world applications. Dual
channel mode is enabled when the installed memory capacities of both DIMM channels are
equal. If different speed DIMMs are used between channels, the slowest memory timing will be
used.
► Enable Clock to All DIMMs
This setting is to control EMI.
When disabled, the system will turn off clock on the empty DIMM slots and to reduce EMI
(Electro-Magnetic Interference).
► MemClk Tristate C3/ALTVID
Enables the DDR memory clocks to be tristated when alternate VID mode is enabled.
► Memory Hole Remapping
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
Memory Configuration
Memory Configuration
Help Item
Bank Interleaving
Enable Bank Memory
Channel Interleaving
[XOR of Address bit]
Interleaving
Enable Clock to ALL DIMMs
[Disabled]
MemClk Tristate C3/ALTVID
[Disabled]
Memory Hole Remapping
[Enabled]
DCT Unganged Mode
[Always]
Power Down Enable
[Disabled]
Optimal Performance Mode
[Disabled]
Auto Tweak Performance
[Disabled]
DRAM Config_High Control
[Auto]
↑↓←→:Move
Enter:Select
+/-/:Value
F10:Save
ESC:Exit
F1:General Help
F9:Optimized Defaults
[Auto]