Foxconn A7DA-S English Manual. - Page 36

► CPU Clock, ► Memory Speed Mode, ► Memory Speed Adjust, ► GFX Engine Clock Override, ► GFX Engine - am2

Get Foxconn A7DA-S PDF manuals and user guides View all Foxconn A7DA-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Fox Intelligent Stepping CMOS Setup Utility - Copyright (C) 1985-2006, American Megatrends, Inc. Fox Intelligent Stepping CPU Clock Memory Speed Mode GFX Engine Clock Override PCI Express Clock CPU Multiplier Adjust Spread Spectrum [200] [Auto] [Disabled] [100] [Auto] [Enabled] Help Item CPU-NB HT Link Speed NCHT Incoming Link Width NCHT Outgoing Link Width Advanced Clock Calibration [Auto] [Auto] [Auto] [Disabled] 3 Move Enter:Select +/-/:Value F10:Save ESC:Exit F1:General Help F9:Optimized Defaults ► CPU Clock This option is used to adjust the CPU clock. ► Memory Speed Mode This item is used to enable/disable provision of DRAM timing by SPD device. The Serial Presence Detect (SPD) device is a small EEPROM chip, mounted on a DDR2 memory module. It contains important information about the module's speed, size, addressing mode and various other parameters, so that the motherboard memory controller (chipset) can better access the memory device. Select [Auto] for SPD enable mode. Select [Limit], the DRAM speed will not exceed the specified value listed in the "Memory Speed Adjust" item. If SPD value is faster than "Memory Speed Adjust" value, it will run at the specified "Memory Speed Adjust" speed. Otherwise, SPD value is selected. Select [Manual], then DRAM speed is manually selected according to the set value of "Memory Speed Adjust". ► Memory Speed Adjust This item will appear only when the "Memory Speed Mode" is set to [Limit] or [Manual]. The available settings are : [400MHz], [533MHz], [667MHz], [800MHz], [1066MHz]. [1066MHz] will appear only in AM2+ CPU. ► GFX Engine Clock Override This item allows you to enable/disable GFX Engine Clock Override support. ► GFX Engine Clock This item will appear only when "GFX Engine Clock Override" is set to [Enabled], it allows you to change the clock rate of graphics engine. You can use the or keys to change the value, or you can type the desired value by using the numeric keypad. ► PCI Express Clock This option is used to adjust the speed of PCI Express slot. It may enhance the graphics card speed. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
3
29
Fox Intelligent Stepping
► CPU Clock
This option is used to adjust the CPU clock.
► Memory Speed Mode
This item is used to enable/disable provision of DRAM timing by SPD device. The Serial
Presence Detect (SPD) device is a small EEPROM chip, mounted on a DDR2 memory
module. It contains important information about the module's speed, size, addressing mode
and various other parameters, so that the motherboard memory controller (chipset) can better
access the memory device.
Select [Auto] for SPD enable mode.
Select [Limit], the DRAM speed will not exceed the specified value listed in the "Memory
Speed Adjust" item. If SPD value is faster than "Memory Speed Adjust" value, it will run at the
specified "Memory Speed Adjust" speed. Otherwise, SPD value is selected.
Select [Manual], then DRAM speed is manually selected according to the set value of
"Memory Speed Adjust".
► Memory Speed Adjust
This item will appear only when the "Memory Speed Mode" is set to [Limit] or [Manual].
The available settings are : [400MHz], [533MHz], [667MHz], [800MHz], [1066MHz].
[1066MHz] will appear only in AM2+ CPU.
► GFX Engine Clock Override
This item allows you to enable/disable GFX Engine Clock Override support.
► GFX Engine Clock
This item will appear only when "GFX Engine Clock Override" is set to [Enabled], it allows you
to change the clock rate of graphics engine. You can use the <+> or <-> keys to change the
value, or you can type the desired value by using the numeric keypad.
► PCI Express Clock
This option is used to adjust the speed of PCI Express slot. It may enhance the graphics card
speed.
CMOS Setup Utility - Copyright (C) 1985-2006, American Megatrends, Inc.
Fox Intelligent Stepping
CPU Clock
[200]
Help Item
Memory Speed Mode
[Auto]
GFX Engine Clock Override
[Disabled]
PCI Express Clock
[100]
CPU Multiplier Adjust
[Auto]
Spread Spectrum
[Enabled]
CPU-NB HT Link Speed
[Auto]
NCHT Incoming Link Width
[Auto]
NCHT Outgoing Link Width
[Auto]
Advanced Clock Calibration
[Disabled]
↑↓←→:Move
Enter:Select
+/-/:Value
F10:Save
ESC:Exit
F1:General Help
F9:Optimized Defaults
200