Foxconn G41AP English Manual. - Page 23

S/PDIF OUT Connector : SPDIF_OUT, Chassis Intrusion Alarm Connector : INTR, F_USB1/2

Get Foxconn G41AP PDF manuals and user guides View all Foxconn G41AP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2 S/PDIF OUT Connector : SPDIF_OUT The connector is used for S/PDIF output. Chassis Intrusion Alarm Connector : INTR The connector can be connected to a security switch on the chassis. The system can detect the chassis intrusion through the function of this connector. If eventually the chassis is closed, the system will send a message out. Floppy Disk Drive Connector : FLOPPY This motherboard includes a standard floppy disk drive (FDD) connector, supporting 360KB, 720KB, 1.2MB, 1.44MB, and 2.88MB FDDs. Front Panel Connector : FP1 This motherboard includes one connector for connecting the front panel switch and LED Indicators. Hard Disk LED Connector (HDD-LED) Connect to the chassis front panel IDE indicator LED. It indicates the active status of the hard disks. This 2-pin connector is directional with +/- sign. Reset Switch (RESET-SW) Attach the connector to the Reset switch on the front panel of the case; the system will restart when the switch is pressed. Power LED Connector (PWR-LED) Connect to the power LED indicator on the front panel of the chassis. The Power LED indicates the system's status. When the system is in operation (S0 status), the LED is on. When the system gets into sleep mode (S1) , the LED is blinking; When the system is in S3/S4 sleep state or power off mode (S5), the LED is off. This 2-pin connector is directional with +/- sign. Power Switch Connector (PWR-SW) Connect to the power button on the front panel of the chassis. Push this switch allows the system to be turned on and off rather than using the power supply button. F_USB1/2 In addition to the four USB ports on the rear panel, this product also provides two 10-pin USB header on its motherboard. By connecting through USB cables with them, user can quickly expand another four USB ports on the front panel. 16 16 +5V 1 EMPTY 2 SPDIF_OUT 3 GND 4 SPDIF_OUT INTRUDERJ 1 INTR GND 1 + HDD-LED- 2 + PWR-LED - RESET-SW PWR-SW NC EMPTY 9 10 FP1 12 VCC DD+ GND EMPTY VCC D- D+ GND NC 9 10 F-USB 1/2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
16
2
16
S/PDIF OUT Connector : SPDIF_OUT
The connector is used for S/PDIF output.
Chassis Intrusion Alarm Connector : INTR
The connector can be connected to a security switch
on the chassis. The system can detect the chassis
intrusion through the function of this connector. If
eventually the chassis is closed, the system will
send a message out.
Floppy Disk Drive Connector : FLOPPY
This motherboard includes a standard floppy disk
drive (FDD) connector, supporting 360KB, 720KB,
1.2MB, 1.44MB, and 2.88MB FDDs.
Front Panel Connector : FP1
This motherboard includes one connector for con-
necting the front panel switch and LED Indicators.
Hard Disk LED Connector (HDD-LED)
Connect to the chassis front panel IDE indicator
LED. It indicates the active status of the hard disks.
This 2-pin connector is directional with +/- sign.
Reset Switch (RESET-SW)
Attach the connector to the Reset switch on the front
panel of the case; the system will restart when the
switch is pressed.
Power LED Connector (PWR-LED)
Connect to the power LED indicator on the front
panel of the chassis. The Power LED indicates the
system’s status. When the system is in operation
(S0 status), the LED is on. When the system gets
into sleep mode (S1) , the LED is blinking; When
the system is in S3/S4 sleep state or power off
mode (S5), the LED is off. This 2-pin connector is
directional with +/- sign.
Power Switch Connector (PWR-SW)
Connect to the power button on the front panel of
the chassis. Push this switch allows the system to
be turned on and off rather than using the power
supply button.
F_USB1/2
In addition to the four USB ports on the rear panel, this
product also provides two 10-pin USB header on its
motherboard. By connecting through USB cables with
them, user can quickly expand another four USB ports
on the front panel.
SPDIF_OUT
+5V
EMPTY
SPDIF_OUT
GND
1
2
3
4
EMPTY
HDD-LED
RESET-SW
NC
+
-
PWR-SW
+
-
PWR-LED
1
2
10
9
FP1
INTR
GND
INTRUDERJ
1
NC
GND
VCC
D+
D-
D+
GND
D-
VCC
EMPTY
1
2
10
9
F-USB 1/2