Frigidaire AEQ8000FS Installation Instructions - Page 10
ELECTRIC Dryer - gas
UPC - 012505377587
View all Frigidaire AEQ8000FS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
2. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer (see pages 6 and 7). Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for a connection. Apply an approved thread sealer that is resistant to the corrosive action of liquefied gases on all pipe connections. 3. Open the shutoff valve in the gas supply line to allow gas to flow through pipe. VALVE OPEN / 4. Test all connections by GAS FLOW POSITION brushing on a soapy water solution. NEVER test for gas leaks with an open flame. ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM USA ELECTRIC Dryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. approved strain relief in the entry hole of the mounting bracket. Finger tighten the nut only at this time. GREEN GROUND SCREW GREEN POWER CORD GROUND WIRE SILVER TERMINAL TERMINAL BLOCK USA ELECTRIC Dryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. approved strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time. GREEN GROUND SCREW NEUTRAL GROUND WIRE SILVER TERMINAL NEUTRAL GROUND WIRE RED BLACK WHITE NUT STRAIN RELIEF MOUNTING BRACKET TIGHTEN NUT TO THESE THREADS POWER CORD 3. Remove the ground wire from the green ground screw located above the terminal block. 4. Thread a U.L. approved 30 amp power cord, NEMA 14-30 type ST or SRDT through the strain relief. NUT TIGHTEN NUT TO THESE THREADS TYPICAL 4 CONDUCTOR TYPICAL 4 CONDUCTOR 30 AMP NEMA 14-30 TYPE SRDT OR ST BLACK WHITE RED GREEN STRAIN RELIEF MOUNTING BRACKET POWER CORD 3. Thread a U.L. approved 30 amp. power cord, NEMA 10-30 type SRDT, through the strain relief. 4. Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw securely. 5. Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tighten both screws securely. Do not make a sharp bend or crimp wiring/ conductor at connections. 6. Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely. 7. Tighten the screws securing the cord restraint firmly against the power cord. 8. Tighten the strain relief nut securely so that the strain relief does not turn. 9. Reinstall the terminal block cover. 5. Attach the green power cord ground wire to the cabinet with the green ground screw. 6. Attach the white (neutral) power cord conductor from the power cord and the neutral ground wire from the dryer harness to the silver-colored center terminal on the terminal block. Tighten the screw securely. 7. Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block. Do not make a sharp bend or crimp wiring/ conductor at the connections. 8. Tighten the screws securing the cord restraint firmly against the power cord. 9. Tighten the strain relief nut securely so the strain relief does not turn. 10.Reinstall the terminal block access cover. 10 Printed in U.S.A.