Frigidaire FAH08ER1T Installation Instructions - Page 2

Wall Sleeve Brands

Get Frigidaire FAH08ER1T - Through-the-Wall 8,000 BTU Air Conditioner PDF manuals and user guides
UPC - 012505271984
View all Frigidaire FAH08ER1T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Wall Sleeve Brands: #1 Emerson 15"Deep Rear Louvers 60° 10-1/4" 1. Redirect the louvers at the back of the wall sleeve as shown in the illustration. The use of pliers is recommended. 60° Top View ← 101⁄4"‹→ 2. Attach (1) 11⁄2"x 3/8"x 261⁄2"long seal as shown in the illustration. 3. Attach the (2) 11⁄2"x 3/8"x 14"long seals, to the inside of the louvered pane. Install the seals as shown in the illustration. 4. Cut the 11⁄2"x 3/8"x 261⁄2"long seal to 14"long, and attach it to the 2 inside of the louvered panel as shown in the illustration. Attach the 3 3 (2) 41⁄2"x 31⁄2"x 11⁄2"Centering/Support Blocks, one on each side wall, to the inside of the sleeve with the Tappered End facing the opening. These (2) blocks should be locaed approximately in the center of the side walls. To attach the blocks remove the backing paper from the blocks. Do not touch adhesive on the blocks. Press the blocks firmly 4 in place. 5. Install the new unit into the wall sleeve. 6 6. Attach the ground wire to the unit as shown. 7. Install the 1"x 11⁄2"x 84"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 7 7 8. Assemble and install the Trim Frame. (see Trim Frame) 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
Wall Sleeve Brands:
Rear Louvers
60
°
10-1/4"
60
°
Top View
#1 Emerson
15
"
Deep
1. Redirect the louvers at the back of the wall sleeve as shown in the
illustration. The use of pliers is recommended.
2. Attach (1) 1
1
∕
2
"
x 3/8
"
x 26
1
∕
2
"
long seal as shown in the illustration.
3. Attach the (2) 1
1
∕
2
"
x 3/8
"
x 14
"
long seals, to the inside of the
louvered pane. Install the seals as shown in the illustration.
4. Cut the 1
1
∕
2
"
x 3/8
"
x 26
1
∕
2
"
long seal to 14
"
long, and attach it to the
inside of the louvered panel as shown in the illustration. Attach the
(2) 4
1
∕
2
"
x 3
1
∕
2
"
x 1
1
∕
2
"
Centering/Support Blocks, one on each side wall,
to the inside of the sleeve with the Tappered End facing the opening.
These (2) blocks should be locaed approximately in the center of the
side walls. To attach the blocks remove the backing paper from the
blocks. Do not touch adhesive on the blocks. Press the blocks firmly
in place.
5. Install the new unit into the wall sleeve.
6. Attach the ground wire to the unit as shown.
7. Install the 1
"
x 1
1
∕
2
"
x 84
"
long stuffer seal between the wall sleeve
and the unit. A flat bladed screwdriver or putty knife is recommended.
8. Assemble and install the Trim Frame. (see Trim Frame)
2
2
3
7
3
4
7
6
←
10
1
∕
4
"‹
→