Frigidaire FCRG3083AD Complete Owners Guide - Page 39

Cooktop Problems, Problem, Cause / Solution

Get Frigidaire FCRG3083AD PDF manuals and user guides View all Frigidaire FCRG3083AD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Cooktop Problems Problem Surface burners do not ignite. Surface burner flame uneven or only part way around burner cap. Surface burner flame is too high. Surface burner flame is orange. 39 BEFORE YOU CALL Cause / Solution Surface control knob was not completely turned to LITE (). Push in and turn the surface control knob to LITE until the burner ignites and then turn the control knob to the desired flame size. Burner ports are clogged. With the burner OFF and cool, use a small-gauge wire or needle to clean the burner head slots and ignition ports. See "Cleaning the surface burners" on page 33 for additional cleaning instructions. Range power cord is disconnected from outlet (electric ignition models only). Be sure the power cord is securely plugged into the power outlet. Circuit is broken. Check breaker box or fuse box. Electrical power outage. Burners may be lit manually. See "Setting Surface Controls" on page 16. Burner slots or ports are clogged. With the surface burner OFF and cool, clean ports with a small-gauge wire or needle. If moisture is present after cleaning, lightly fan the flame and allow the burner to operate until flame is full. Burner caps are not seated properly. Check that all burner caps are level and seated correctly on the burner heads. See "Cleaning the surface burners" on page 33 for additional cleaning instructions. Surface control knob is set too high. Adjust to a lower flame setting. Burner caps are not seated properly. Check that all surface burner caps are level and seated correctly on the surface burner heads. See "Cleaning the surface burners" on page 33 for additional cleaning instructions. Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct. Dust particles in main gas line. Allow the burner to operate a few minutes until flame turns blue. In coastal areas, a slightly orange flame is unavoidable due to salt content in the air. Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
39
BEFORE YOU CALL
Cooktop Problems
Problem
Cause / Solution
Surface burners do not
ignite.
Surface control knob was not completely turned to LITE (). Push in and turn
the surface control knob to LITE until the burner ignites and then turn the
control knob to the desired flame size.
Burner ports are clogged. With the burner OFF and cool, use a small-gauge
wire or needle to clean the burner head slots and ignition ports. See “Clean-
ing the surface burners” on page 33 for additional cleaning instructions.
Range power cord is disconnected from outlet (electric ignition models
only). Be sure the power cord is securely plugged into the power outlet.
Circuit is broken. Check breaker box or fuse box.
Electrical power outage. Burners may be lit manually. See “Setting Surface
Controls” on page 16.
Surface burner flame
uneven or only part way
around burner cap.
Burner slots or ports are clogged. With the surface burner OFF and cool,
clean ports with a small-gauge wire or needle. If moisture is present after
cleaning, lightly fan the flame and allow the burner to operate until flame is
full.
Burner caps are not seated properly. Check that all burner caps are level
and seated correctly on the burner heads. See “Cleaning the surface burn-
ers” on page 33 for additional cleaning instructions.
Surface burner flame is
too high.
Surface control knob is set too high. Adjust to a lower flame setting.
Burner caps are not seated properly. Check that all surface burner caps are
level and seated correctly on the surface burner heads. See “Cleaning the
surface burners” on page 33 for additional cleaning instructions.
Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.
Surface burner flame is
orange.
Dust particles in main gas line. Allow the burner to operate a few minutes
until flame turns blue. In coastal areas, a slightly orange flame is unavoid-
able due to salt content in the air.
Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.