Frigidaire FFTA1033Q1 Installation Instructions - Page 10

Use these next steps if the unit requires extra extension into

Get Frigidaire FFTA1033Q1 PDF manuals and user guides View all Frigidaire FFTA1033Q1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Installation Instructions Wall Sleeve Brands: #7 Whirlpool 23" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match 80º new rear grille Because of the increased unit depth, first try dry fitting using the method described below: 2. Place (2) 1" x 11 2" x 14" seals against each side. 3. Gently slide unit in and check if amount extending from the sleeve is sufficient once the trim frame is attached. 4. If position is okay, remove unit and Proceed to the next step.If not go to step 9. 5. Attach (1) 1" x 1 1 2" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 6. Attach (2) 1" x 1 1 2" x 14" seals to the left and right sides of the sleeve. 7. Cut (2) 1" x 3/8" x 25" long seal to 14" long each and attach to the vertical sections of the grille as shown. 8. Attach the tapered spacer blocks to the floor of the sleeve. Now go to step 15. Use these next steps if the unit requires extra extension into the room. 9. Attach 1" x 3 4 " x 14" long seal over the solid vertical portion of the rear grille. 10. Attach (2) 43 4" x 33 4" x 13 4" foam blocks with the slot overlapping the seal above. 11. Install the divider into the slots of the foam blocks. You may need to trim the length to size. 12. Repeat steps 9-11 for the other vertical shown portion of the grille as shown in the picture. 13. Attach (2) 1" x 11 2 " x 14" seals along the sides of the sleeve again making sure all seals are flush. 14. Cut the 1" x 11 2" x 25" seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider. 15. Center unit & gently slide unit into sleeve. 16. Before sliding all-the-way back, remove 2nd screw from front on left side of unit. 17. Remove the plastic washer from the screw. 18. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet. 19. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. 20. Seal & Frame the unit as described on the last page of these instructions. 21. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page 13. 10 Rear Louvers 4.5" 50º 50º 4" 80º Top View 4.5" 4" 4.5" 4"

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
Installation Instructions
#7 Whirlpool
Wall Sleeve Brands:
1.
Remove existing rear grille as shown on Page 3 of this manual and
replace with provided louvered rear panel. Install as shown here.
80º
50º
50º
Rear Louvers
80º
Top View
23
” Deep
Because of the increased unit depth, first try dry fitting using
the method described below:
Use these next steps if the unit requires extra extension into
the room.
2.
Place (2) 1" x 1
" x 14" seals against each side.
1
2
11. Install the divider into the slots of the foam blocks. You may need to
trim the length to size.
12. Repeat steps 9-11 for the other vertical shown portion of the grille as
shown in the picture.
9.
Attach 1" x
" x 14" long seal over the solid vertical portion of the rear
grille.
3
4
10. Attach (2) 4
" x 3
" x 1
" foam blocks with the slot overlapping the
seal above.
3
4
3
4
3
4
13. Attach (2) 1" x 1
" x 14" seals along the sides of the sleeve again
making sure all seals are flush.
1
2
15. Center unit & gently slide unit into sleeve.
16. Before sliding all-the-way back, remove 2nd screw from front on left
side of unit.
17. Remove the plastic washer from the screw.
19. Slide the unit completely to the rear to ensure a good seal, making
sure the ground wire does not become tangled.
20. Seal & Frame the unit as described on the last page of these instructions.
14. Cut the 1" x 1
" x 25" seal to fit the top of the sleeve. The pieces must
be fitted flush to the edge of the divider.
1
2
4.
If position is okay, remove unit and Proceed to the next step.If not go
to step 9.
1
2
5.
Attach (1) 1" x 1
" x 25" long seal in the center at the top of the
sleeve. Remove the backing paper and press into position.
1
2
6.
Attach (2) 1" x 1
" x 14" seals to the left and right sides of the sleeve.
7.
Cut (2) 1" x 3/8" x 25" long seal to 14" long each and attach to the
vertical sections of the grille as shown.
8.
Attach the tapered spacer blocks to the floor of the sleeve. Now go to
step 15.
3.
Gently slide unit in and check if amount extending from the sleeve is
sufficient once the trim frame is attached.
10
NOTE:
You may need to drill holes in flange of existing sleeve to match
new rear grille
21. If you have difficulty with mounting the grill to the sleeve, follow the
instructions for direct mounting on Page 13.
18.
Screw and attach the other end of the ground wire from sleeve to the
unit as shown in picture. Make sure that the toothed washer is against
the cabinet.
4.5"
4"
4.5"
4"
4.5"
4"