Frigidaire FHPC102AB1 Complete Owners Guide - Page 14

Heat modeFor Heat & Cool models only, Auto mode, Sleep mode, Louver Swing Function

Get Frigidaire FHPC102AB1 PDF manuals and user guides View all Frigidaire FHPC102AB1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Operating Instructions Heat mode(For Heat & Cool models only) Press the "mode" button until the left side of LCD screen displays "heat". Press the " " and " " button to choose the temperature you want. Press the " fan speed" button to choose the fan speed "auto", "high", "mid", and "low". Note: In this mode, condensate drainage are required, refer to the "Drainage Instructions" on Page 16-17 for more instructions to drain the excess condensate. Auto mode Press the "mode" button until the left side of LCD screen displays "auto". Press the " " and " " button to choose the temperature you want. In this mode, the unit will automatically select cooling, heating(not applicable for cooling only models), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you. Note: In this mode, fan speed cannot be selected. Sleep mode When the unit is in Cool, Heat or Auto mode, you can press the "sleep" button to make the unit run in Sleep mode. In this mode, the fan speed will be set as "auto" automatically, which cannot be changed. In Cool/Heat mode the selected temperature will increase/decrease by 2 °F 30 minutes after the mode is selected. The temperature will then increase/decrease by another 2 °F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" mode and the unit will continue to operate as originally programmed. The "Sleep" mode program can be cancelled at any time during operation by pressing the "Sleep", "mode", "fan speed" or "on·off" button. Note: In Fan or Dry mode, Sleep mode cannot be set. Louver Swing Function Press the "swing" button to enable louver swing function, and the upper side of screen will display " ". The louver on the top panel will swing up and down. Press this button again to disable the louver swing function. Fig.19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Press the “mode” button until the left side of LCD
screen displays “heat”.
Press the “
” and “
” button to choose the temperature you want.
Press the “swing” button to enable louver swing function,
and the upper side of screen will display “
”. The louver
on the top panel will swing up and down.
Press this button again to disable the louver swing function.
Press the “mode” button until the left side of LCD
screen displays “auto”.
Press the “
” and “
” button to choose the temperature you want.
In this mode, the unit will automatically select cooling, heating(not applicable for
cooling only models), or fan only operation depending on what temperature you
have selected and the room temperature. The air conditioner will control room
temperature automatically round the temperature point set by you.
Note: In this mode, fan speed cannot be selected.
When the unit is in Cool, Heat or Auto mode, you can press the “sleep” button
to make the unit run in Sleep mode. In this mode, the fan speed will be set as “auto”
automatically, which cannot be changed.
In Cool/Heat mode the selected temperature will increase/decrease by 2 °F 30
minutes after the mode is selected. The temperature will then increase/decrease by
another 2 °F after an additional 30 minutes. This new temperature will be maintained
for 7 hours before it returns to the originally selected temperature. This ends the
"Sleep" mode and the unit will continue to operate as originally programmed.
The "Sleep" mode program can be cancelled at any time during operation by
pressing the "Sleep", “mode”, “fan speed” or “on·off” button.
Note: In Fan or Dry mode, Sleep mode cannot be set.
Heat mode(For Heat & Cool models only)
Auto mode
Sleep mode
Louver Swing Function
Operating Instructions
Fig.19
Press the “ fan speed” button to choose the fan speed
“auto”, “high”, “mid”, and “low”.
Note: In this mode, condensate drainage are required, refer to the
"Drainage Instructions" on Page 16-17 for more instructions to drain
the excess condensate.