Frigidaire FPIC3677RF Wiring Diagram - Page 1

SERVICE DATA SHEET 36" INDUCTION COOKTOP NOTICE - This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The manufacturer cannot be responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet. SAFE SERVICING PRACTICES To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be observed. The following are examples, but without limitation, of such practices. 1. Before servicing or moving an appliance remove power cord from electrical outlet, trip circuit breaker to OFF, or remove fuse. 2. Never interfere with the proper installation of any safety device. 3. GROUNDING: The standard color coding for safety ground wires is GREEN or GREEN WITH YELLOW STRIPES. Ground leads are not to be used as current carrying conductors. It is extremely important that the service technician reestablish all safety grounds prior to completion of service. Failure to do so will create a potential safety hazard. 4. Prior to returning the product to service, ensure that: • All electric connections are correct and secure. • All electrical leads are properly dressed and secured away from sharp edges, high-temperature components, and moving parts. • All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels. • All safety grounds (both internal and external) are correctly and securely reassembled. GENERATOR/POWERBOARD-RIGHT (3) CARTE GENERATEUR-DROIT (3) BPN1 BPN2 BPL2 BPL1 BPE03 TAB101 TAB102 B81 BC3 BC4 BC5 BC1 THERMAL CUT-OUT COUPE-CIRCUIT THERMIQUE B71 TAB1 TAB2 Electronic Surface Element Control (ESEC) This cooktop is equipped with an Electronic Surface Element Control (ESEC), which precisely controls the smoothtop cooking elements at multiple settings. For the user, the elements are operated by the knobs. The control settings are shown in 2-digit displays. Hot Surface display message - If any of the induction elements are hot, the hot surface message (HE) will display and remain ON until the cooktop cools. Replacing an induction element Whenever replacing any induction element use only the screws supplied with the range to secure the element to the mounting panel. Never use any other type of screw to attach the induction element. * Please note: Electronic boards are very sensitive to static electricity. Static electricity can permanently damage electronic boards. Before handling these parts, be sure to drain static electricity from your body by properly grounding yourself. ID JUMPER: ADDRESS 3 CONNECT RED JUMPER TO BC1 IDENTIFICATEUR: ADRESSE 2 BRANCHEZ EN UTILISANT FAISCEAU-FIL ROUGE BC1 THERMAL CUT-OUT COUPE-CIRCUIT THERMIQUE BPE03 GENERATOR/POWERBOARD-CENTER (2) CARTE GENERATEUR-CENTRE (2) IMPORTANT DO NOT REMOVE THIS BAG OR DESTROY THE CONTENTS WIRING DIAGRAMS AND SERVICE INFORMATION ENCLOSED REPLACE CONTENTS IN BAG p/n A00498604 Rev B (1603) GENERATOR/POWERBOARD-LEFT (1) CARTE GENERATEUR-GAUCHE (1) BPN1 BPN2 BPL2 BPL1 BPE03 BPN1 BPN2 BPL2 BPL1 TAB101 TAB102 B81 BC3 BC4 BC5 BC1 B71 TAB1 TAB2 ID JUMPER: ADDRESS 2 DO NOT CONNECT BLACK JUMPER TO BC5 OR BC1 IDENTIFICATEUR: ADRESSE 2 NE PAS BRANCHEZ EN UTILISANT FAISCEAU-FIL NOIR BC5 OU BC1 Indicated 0 Lo 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 Hi Pb % Power 0 7 9 12 15 17 18 19 20 21 25 31 38 45 50 54 59 64 80 100 138-152 Notes Off Keep Warm - - - PowerBoost THERMAL CUT-OUT COUPE-CIRCUIT THERMIQUE TAB101 TAB102 B81 BC3 BC4 BC5 BC1 B71 TAB1 TAB2 BC3 TO USER INTERFACE BOARD Á PLAQUETTE D'INTERFACE DE UTILISATEUR ID JUMPER: ADDRESS 1 DO NOT CONNECT BC1 IDENTIFICATEUR: ADRESSE 2 NE PAS BRANCHER BC1