Frigidaire GLCS389FQ Installation Instructions - Page 9

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS (Models with an Electric Oven and a Gas Cooktop) 7. Moving the Appliance for Servicing and Cleaning Turn off the range line fuse or circuit breakers at the main power source, and turn off the manual gas shut-off valve. Make sure the range is cold. Remove the service drawer (warmer drawer on some models) and open the oven door. Lift the range at the front and slide it out of the cut-out opening without creating undue strain on the flexible gas conduit. Make sure not to pinch the flexible gas conduit at the back of the range when replacing the unit into the cutout opening. Replace the drawer, close the door and switch on the electrical power and gas to the range. 8. Range Installation Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. Refer to the Use and Care Guide for oven door removal instructions. the unit by lowering the leveling legs. 11.Level the range (see section 9). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range". 12. Adjust leveling legs so that the underside of the cooktop is sitting on the countertop. 13. Carefully screw in the back leveling leg until the cooktop glass overhang touches slightly the countertop. The cooktop glass must not support the unit. 14. Then carefully screw in the front two leveling legs (similar to 13) until the glass overhang touches slightly the countertop. 15.If the range is not level, pull unit out and readjust leveling legs, or make sure floor is level. Installation For 29" Existing Cutout Wide Opening 1. You must replace the actual side trims by new and smaller side trims. These new side trims can be ordered through a Service Center. 2. Follow instructions supplied with your new side trims to replace the actual side trims with the new ones. 3. Check if the countertop is prepared for 29" cutout wide opening in "Countertop Preparation" section. 4. Install range as in the "Installation Without Side Panels" section above. Standard Installation 1. The range cooktop overlaps the countertop at the sides and the range rests on the floor. The cooktop is 31½" (1,27 cm) (81 cm) wide. 2. Install base cabinets 30" (76.2 cm) apart. Make sure they are plumb and level before attaching cooktop. Shave raised countertop edge to clear 31 1/2"(1,27 cm) wide range top rim. 3. Install cabinet doors 31" (78.7 cm) min. apart so it will not interfere with range door opening. 4. Cutout countertop exactly as shown on page 1. 5. A backguard kit can be ordered through Service Center. 6. When you unpack the range, the leveling legs at rear are at the highest position they can be. Make sure the front leveling legs are also at their highest position. 7. To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. 8. To reduce the risk of damaging your appliance, do not handle or manipulate it by the ceramic glass. Manipulate with care. 9. Position range in front of the cabinet opening. 10. Make sure that the glass which overhangs the countertop clears the countertop. If necessary, raise Installation With Backguard The cutout depth of (21 3/4" (55.2 cm) Min., 22 1/8" (56.2 cm) Max.) needs to be increased to 24"(10,16 cm) (61 cm) when installing a backguard. Installation With End Panel A End Panel kit can be ordered through a Service Center. Installation With Side Panels A Side Panels kit can be ordered through a Service Center. Install cabinet doors 31" (78.7 cm) min. apart so as not to interfere with range door opening. 9