Frigidaire IM115 User Manual
Frigidaire IM115 - Ice Maker Kit Manual
 |
UPC - 012505733819
View all Frigidaire IM115 manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire IM115 manual content summary:
- Frigidaire IM115 | User Manual - Page 1
ICE MAKER INSTALLATION INSTRUCTIONS To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. To Avoid Property Damage: • Copper tubing is recommended for the water supply - Frigidaire IM115 | User Manual - Page 2
Use This Page to Identify Parts 1. Ice Maker 2. Ice Container 3. Plastic Water Supply Tubing 4. Screws - Qty 2 5. Screws - Qty 2 6. Leveling Bracket Screw - Qty 1 7. Leveling Bracket Qty 1 8. Steel Clamp - Qty 1 9. Plastic Clamp - Qty 2 10. Water Valve - Qty 1 11. Water Inlet Tube - Qty 1 - Frigidaire IM115 | User Manual - Page 3
label covering ice maker hole. 7. With needle nose pliers, remove foam from hole. 5. If refrigerator has exterior condenser (C), go to rear of refrigerator and locate left condenser mounting bracket screw(s). Remove and save screws. DO NOT remove compressor sound baffle (A), if installed.Carefully - Frigidaire IM115 | User Manual - Page 4
turn with a wrench. DO NOT over tighten. 12. With ice maker in one hand, plug ice maker connector into connector mounted on back freezer panel. Make sure connection is tight. 10. Install adjustable leveling bracket (7) on bottom of ice maker with screw (6). DO NOT tighten bracket. (Bracket will be - Frigidaire IM115 | User Manual - Page 5
shelf in lower position. Set ice container (2) on shelf. 18 wiring harness to water valve. Make sure connection is tight. 20. On models with exterior condenser, reinstall condenser brackets and tighten down screws. 21. On refrigerators with dynamic condensers, remount sound baffle, if installed - Frigidaire IM115 | User Manual - Page 6
and instructions for installing a water supply line. To Connect Water Supply Line To Ice Maker Inlet Valve 1. Disconnect refrigerator from electric connections that leak. 9. Reconnect refrigerator to electric power supply. 10.To turn ice maker on, lower wire signal arm. (See ice maker front cover - Frigidaire IM115 | User Manual - Page 7
signal arm is in its “down” or ON position. The ice maker will then produce more ice. • Occasionally shake the container to keep ice separated. • Keep the wire signal arm in its “up” or OFF position until the refrigerator is connected to the water supply or whenever the water supply is turned off
-
1 -
2 -
3 -
4 -
5 -
6 -
7
 |
 |
ICE MAKER
INSTALLATION
INSTRUCTIONS
P/N 240394901
The following items will be required to install the ice maker kit.
•
1/4 inch copper supply line with shut off valve
•
1/4 inch brass compression nut and ferrule
•
Freezer shelf (Some models not eqipped with shelf). If your
model does not have one, contact your dealer to order one.
The copper tubing and shut off valve are available in a kit from your
local hardware or plumbing supply store.
Coil enough tubing at the
back of the unit to allow movement for cleaning.
To Avoid Property Damage:
•
Copper tubing is recommended for the water supply line. Water supply tubing made of
1/4
”
plastic is not recommended since it greatly increases the potential for water leaks.
The manufacturer will not be responsible for any damage if plastic tubing is used for the
supply line.
•
DO NOT
install water supply tubing in areas where temperatures fall below freezing.
•
Connect the ice maker to a drinkable water source that is not tied into a water softening
system. Chemicals from the softener may damage the ice maker, causing it to
malfunction.
To avoid electric shock, which can cause death or severe personal injury,
disconnect the refrigerator from electrical power before connecting a water supply line to
the refrigerator.