Garmin Foretrex 201 Quick Start Guide - Page 1
Garmin Foretrex 201 - Hiking GPS Receiver Manual
UPC - 753759045302
View all Garmin Foretrex 201 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Foretrex 201 Features Foretrex 201 Features Foretrex 201 Features Foretrex 201 Features Foretrex™ 201 Using the Map Page The Map Page shows where you are (the animated figure) and provides a picture of where you are going. As you travel, the animated figure 'walks' and leaves a 'trail' or 'track log'. Waypoint names and symbols are also shown on the map. Map Page To use the Map Page while moving around: 1. Press the PAGE button until the Map Page is displayed. Press the DOWN button to zoom in for a more detailed view of the map. Press the UP button to zoom out for a view of a larger map area. 2. Walk or drive around for a few minutes, make a right or left turn, then continue for a few more minutes and stop. Marking a Waypoint Waypoints are locations or landmarks worth recording and storing in your GPS. These are locations you may later want to return to, such as check points on a route or significant ground features like your campsite or a favorite fishing spot. Waypoints may be defined and stored in the unit manually by taking coordinates for the waypoint from a map or other reference. This can be done before ever leaving home. Or more usually, waypoints may be entered directly by taking a reading with the unit at the location itself, giving it a name, and then saving the point. To mark your current location as a waypoint: 1. Press and hold the ENTER/MARK button for two seconds to display the Mark Waypoint Page. Your current location is marked as a waypoint and assigned a three-digit number. 2. The 'OK' button is highlighted so press the ENTER/MARK button again to save the Waypoint. Navigating to a Location Basic navigation with your Foretrex requires only three steps: mark, move, and return. Mark your location as a waypoint, move a distance away, and then return after choosing one of several methods, such as using a GoTo or following a virtual breadcrumb trail. To return to a waypoint using the GOTO button: 1. Press the GOTO button to display the GoTo Waypoint Page. 2. Use the UP and DOWN buttons to select the desired tab and press ENTER. 3. Use the UP and DOWN buttons to select the waypoint you would like to route to and press ENTER. The Navigation Page automatically displays to lead you to the waypoint. Using the Navigation Page The Navigation Page helps guide you to a destination: Just follow the arrow in the center of the compass. Navigation Page To use the Navigation Page to get to a destination: 1. With a destination already selected and a navigation started, press the PAGE button repeatedly until the Navigation Page is displayed, if it is not already. 2. The Navigation Page displays a Pointer indicating the direction to go. Because you can't always travel in a straight line, refer to the Pointer from time to time. As you move and whenever possible, turn in the direction the Pointer directs until it points straight up. At which time, travel forward until you arrive at your destination. 3. To stop navigating, press the ENTER button while on either the Map or Navigation page. Use the UP/DOWN buttons to highlight 'STOP NAVIGATION', and then press the ENTER button. Using Tracks The Foretrex 201 automatically draws an electronic breadcrumb trail or 'track log' on the Map Page as you travel. Tracks are marked BEGIN and END. The Foretrex 201 uses the Track Log to allow you to navigate using the saved track or using the TracBack feature. TracBack guides you to where you started by following the track log that you left behind, allowing you to return along a traveled path without marking any waypoints. You can retrace your track in both directions. If you want to keep a record of a certain track log or use the 'TracBack' feature, clear the Track Log before you start traveling. To navigate using TracBack: 1. Press the PAGE button to access the Main Menu. 2. Use the UP and DOWN arrows to highlight 'TRACKS' and press ENTER to open the Tracks Menu Page. 3. Use the UP and DOWN arrows to highlight 'PAN & TRACBACK' and press ENTER. 4. Use the UP and DOWN arrows to pan the track log. Press ENTER to display the Pan Options. Panning the Track Log 5. Use the UP and DOWN arrows to select 'TRACBACK' and press ENTER. 6. The Navigation Page displays a Pointer indicating the direction to go. Follow the arrow as you would for a normal navigation. To clear the track log: 1. From the Map Page, press ENTER to access the Map Page Options. Use the UP and DOWN buttons to select 'CLEAR TRACK LOG' and press ENTER Or From the Main Menu, press ENTER when 'TRACKS' is highlighted to open the Tracks Menu Page. Use the UP and DOWN arrows to highlight 'CLEAR TRACK' and press ENTER. 2. Use the UP and DOWN arrows to highlight 'YES' on the pop-up window and press ENTER to clear the track log. Using Routes Route navigation allows you to create a sequence of waypoints to lead you to your final destination. To create a route: 1. From the Main Menu Page press the UP or DOWN button to highlight 'ROUTES', then press the ENTER button. 2. Select 'CREATE NEW' and press ENTER. Press ENTER to display the 'ADD POINT TO ROUTE PAGE'. 3. Use the UP/DOWN and ENTER buttons to select the desired waypoint and press ENTER. Repeat until all of the desired waypoints are in the route. Route Page The route is automatically named with the first waypoint and the last waypoint, such as Camp-Dock. Press PAGE to exit the Route Page and return to the Route Menu. Use the UP and DOWN buttons to highlight 'DELETE' and press ENTER to delete the entire route. Use the UP and DOWN buttons to highlight 'FOLLOW' and press ENTER to follow the route. Using the Timer After the Timer Page is enabled and a count down time is entered, you can use the timer for a variety of applications, such as running and sailboat racing. The synchronization and quick reset capabilities make the Foretrex an extremely handy timer. To stop and start the timer: 1. Press the PAGE button until the Timer Page is displayed. 2. To start the timer, press the ENTER button when 'START' is displayed along the bottom of the page. 3. To stop the timer, press the ENTER button when 'STOP' is displayed along the bottom of the page. QUICK START GUIDE Built-in GPS Antenna Waterproof Case LCD Display (with Backlight) Power Button (Backlight) Up/Down Buttons Step-by-Step Instructions to Get You Started (Turn this page and begin with Step 1) *Flip this Quick Start Guide over for a detailed explanation of the Foretrex 201 buttons. Part Number 190-00353-01 Rev B