Garmin Foretrex 201 Quick Start Guide - Page 2

Foretrex 201 Setup Foretrex 201 Setup Foretrex 201 Setup Foretrex 201 Setup Foretrex 201 Buttons 1 Charging the Foretrex 201 The Foretrex operates on a built-in battery. Before using the Foretrex, you must charge the internal battery. To charge the Foretrex 201: 1. Wipe the contacts dry, if needed. 2. Snap the Cradle to the unit with the 4-contact end in first (shown above). 3. Connect the AC Charging Cable in to the connector labeled "5.0V DC" on the Charging Cradle. 4. Connect the AC Charging Cable to a power source. The mes- sage "Battery Charging in Progress" appears on the Foretrex's screen when it is charging. 5. Leave the Foretrex until it is completely charged, at least two (2) hours. When the message "Battery Charging Completed" appears on the screen, the unit is fully charged and ready for use. Foretrex 201 Battery Life When the Foretrex is fully charged, you should get about 15 hours out of the battery before it needs to be charged again. The Foretrex charges in about one to three hours. 2 Starting Up the Foretrex 201 After the Foretrex is completely charged, it is ready for use. To turn on the Foretrex 201: 1. Press and hold the POWER button until the Satellite Page is displayed. 2. Allow the Foretrex time to track satellites the first time you use it. Leave the Foretrex outside with a clear view of the sky for 15-30 minutes. After the first use, it should take less than one (1) minute to acquire satellites. 3. When the Foretrex acquires enough satellite signals to determine your location, "3D GPS FIX" or "2D GPS FIX" is displayed, and the satellite dish icon in the upper left corner of the screen stops flashing. Also, the Signal bar fills up to show the strength of the satellite signal. Foretrex 201 Icons Two icons in the upper left-hand corner provide at-aglance-status of the Foretrex: battery and satellite dish icon. Battery icon: The battery icon indicates how much battery power is left before the unit must be charged. A full battery icon indicates a fully-charged battery. Timer icon: When the timer feature of the Foretrex is being used, the timer icon displays just below the battery icon. Satellite Dish icon: When the Foretrex has acquired enough satellites to establish your GPS location fix, this icon displays solid (not flashing) just below the timer icon. The Satellite Dish icon flashes while it is acquiring satellites and determining your location. 3 Changing the Pages Press the PAGE button to cycle through the main pages: The Satellite Page, Map Page, Navigation Page, Trip Computer, Timer Page (if enabled), and the Menu Page. Satellite Page - Provides notice of satellites being tracked. Map Page - Displays your movements. Navigation Page - Provides guidance to your destination. Trip Computer Page - Provides information about your trip, such as speed, maximum speed, and current location. The data fields are completely customizeable to fit your needs. Timer Page (if enabled) - Provides an advanced timer great for a variety of applications such as sailboat racing. Menu Page - Provides access to features and settings. Refer to the Foretrex Owner's Manual for complete information on all of the Foretrex's pages. 4 Setting the Time Zone When the Foretrex is ready for use, you may need to check the Time Zone selection. The time is set automatically as soon as the unit establishes a fix on the GPS satellites. The current date and time is displayed on the top of the screen. When the Foretrex has established a GPS fix, U.S. Central Time is selected as the default Time Zone. To change the Time Zone: 1. Press the PAGE button to display the Menu Page. 2. Press the DOWN button to highlight 'SETUP'. Press ENTER. 3. Press Enter when 'SET TIME' is highlighted. 4. To change the Time Zone, use the UP/DOWN buttons to select 'TIME ZONE' and press ENTER. 5. Use the UP/DOWN buttons to select the correct time zone and press ENTER. 5 Adjusting the Display To adjust the light timeout and contrast: 1. Use the PAGE button to access the Satellite Page. 2. Press and release the ENTER button to display the Options Menu. 3. Press ENTER to display the Display Setup Page. 4. Press ENTER when the line below "LIGHT TIMEOUT" is high- lighted. Use the UP/DOWN buttons to select the desired length of time for the backlight timeout. Press ENTER to select the highlighted length of time. 5. Use the UP/DOWN buttons to select the slider bar below the 'CONTRAST' field. Press the Enter button to select the slider bar to adjust the contrast. Use the UP/DOWN buttons to adjust the contrast. Press ENTER when done. To turn the backlight On and Off: 1. Press the POWER button to turn the backlight On. 2. Press POWER again to turn the backlight Off. 3. If no other button is pressed, the backlight turns off automati- cally after 30 seconds or whatever time you have set through the Display Setup Page, which can be accessed from the Main Menu or the Satellite Page. 5 Adjusting the Strap The Foretrex has been designed to comfortably fit your wrist. A strap extension provides additional length and easily attaches to the existing strap. To add the strap extension: 1. Slide the end of the existing strap through the connector on the extension. 2. Place on your wrist or arm. 3. Slide the end of the extension through the existing connector. 4. Adjust to fit comfortably and secure the strap. Refer to the Owner's Manual for complete instructions. Usifnorgetrtehx e201Foretrex 201 Buttons goto page enter mark POWER GOTO PAGE The POWER button: ENTER/ MARK DOWN UP • Press and hold to turn unit on and off • Press and release to turn display backlight on and off • Press and hold PAGE, then simultaneously press POWER to reset the unit if it is hung up or frozen The GOTO button: • Press to initiate a GoTo (navigate to a specific destination/ waypoint) The PAGE button: • Press to switch between the main Pages • Press to back out or escape out of the present page or screen The ENTER/MARK button: • Press to confirm data entry or menu selection • Press and hold to mark a waypoint The UP/DOWN buttons: • Highlight options on pages and menus • Adjust display contrast • Zoom out (UP) and in (DOWN) on Map Page • Cycle through data fields on Navigation Page