Garmin Intelliducer NMEA 2000 0-12 Tilt Installation Instructions - Page 9

Step 4 NMEA 0183: Connect the Intelliducer to Power and a NMEA, compliant Device, Exceptions

Get Garmin Intelliducer NMEA 2000 0-12 Tilt PDF manuals and user guides View all Garmin Intelliducer NMEA 2000 0-12 Tilt manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Step 4 (NMEA 0183): C��o�n�n�e��c�t�t�h�e��In��te��ll�id��u�c�e�r��to��P��o�w��e�r�a�n��d��a�N��M��E�A� 0183-compliant Device Follow these instructions to connect a NMEA 0183 Thru-Hull Intelliducer. If you have a NMEA 2000 Thru-Hull Intelliducer, see Step 4 (NMEA 2000). The Thru-Hull NMEA 0183 Intelliducer must be connected to power. Use the diagrams to correctly wire the Inteliducer. In the diagrams, Tx = transmit, and Rx = receive. You can connect up to three NMEA 0183-compliant devices to receive data from one Intelliducer. Color Fuse Red 2 A Black Orange > Gray > White/Red White White/ Orange Function Power Ground Acc. On Tx A(+) Tx B(-) Spare Spare > > Thru-Hull NMEA 0183 Intelliducer Power/Data Cable NMEA 0183 Intelliducer +Battery- Fuse 12 Vdc 2 A Red Black Orange > Gray > White/Red Power Ground ACC On Rx A(+) > Rx B(-) > NMEA 0183Compliant Device Thru-Hull NMEA 0183 Intelliducer Wired to a NMEA 0183-compliant Device Exceptions: • If your NMEA 0183-compliant device has only one receiving wire (Rx), connect it to the gray wire (Tx/A) from the Intelliducer, and leave the white/red wire (Tx/B) from the Intelliducer unconnected. Note: The orange (accessory on) wire is used when wiring the Intelliducer to a Garmin chartplotter, or other NMEA 0183 device that has a defined accessory signal wire. If you are wiring the Intelliducer to a device that does not have an accessory signal wire, the orange wire from the Intelliducer should be connected to ground. caution: If you are wiring the Intelliducer to a device that does not have an accessory signal wire, connect the Intelliducer power wire to the ignition or install an in-line switch. The Intelliducer can drain the battery of the boat if it is not switched. Thru-Hull Intelliducer Installation Instructions 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Thru-Hull Intelliducer Installation Instructions
Step 4 (NMEA 0183): Connect the Intelliducer to Power and a NMEA
Connect the Intelliducer to Power and a NMEA
0183-compliant Device
Follow these instructions to connect a NMEA 0183 Thru-Hull Intelliducer. If you have a
NMEA 2000 Thru-Hull Intelliducer, see Step 4 (NMEA 2000).
The Thru-Hull NMEA 0183 Intelliducer must be connected to power. Use the diagrams to
correctly wire the Inteliducer. In the diagrams, Tx = transmit, and Rx = receive. You can
connect up to three NMEA 0183-compliant devices to receive data from one Intelliducer.
>
>
>
>
Color
Red
Black
Orange
Gray
White/Red
White
White/
Orange
Function
Power
Ground
Acc. On
Tx A(+)
Tx B(-)
Spare
Spare
Fuse
2 A
Thru-Hull NMEA 0183 Intelliducer Power/Data Cable
+
-
>
>
>
>
NMEA 0183-
Compliant
Device
Orange
Red
Black
Power
Ground
ACC On
NMEA 0183
Intelliducer
Gray
White/Red
Rx A(+)
Rx B(-)
Fuse
2 A
Battery
12 Vdc
Thru-Hull NMEA 0183 Intelliducer Wired to a NMEA 0183-compliant Device
Exceptions:
If your NMEA 0183-compliant device has only one receiving wire (Rx), connect it to
the gray wire (Tx/A) from the Intelliducer, and leave the white/red wire (Tx/B) from the
Intelliducer unconnected.
NOTE:
The orange (accessory on) wire is used when wiring the Intelliducer to a Garmin
chartplotter, or other NMEA 0183 device that has a defined accessory signal wire. If you are wiring
the Intelliducer to a device that does not have an accessory signal wire, the orange wire from the
Intelliducer should be connected to ground.
CAUTION:
If you are wiring the Intelliducer to a device that does not have an accessory
signal wire, connect the Intelliducer power wire to the ignition or install an in-line switch. The
Intelliducer can drain the battery of the boat if it is not switched.
•