Garmin babyCam Bundle Owners Manual - Page 17
Troubleshooting, Appendix
View all Garmin babyCam Bundle manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
• Remove the device and mount from sight when not in use. • Remove the residue left on the windshield by the suction cup. • Do not keep your unit in the glove compartment. • Register your device at http://my.garmin.com. Resetting the Device You can reset your device if it stops functioning. Hold the power key for 12 seconds. Removing the Device, Mount, and Suction Cup Removing the Device from the Mount 1 Press the release tab or button on the mount. 2 Tilt the device forward. Removing the Mount from the Suction Cup 1 Turn the device mount to the right or left. 2 Apply pressure until the socket on the mount releases the ball on the suction cup. Removing the Suction Cup from the Windshield 1 Flip the lever on the suction cup toward you. 2 Pull the tab on the suction cup toward you. Changing the Fuse in the Vehicle Power Cable NOTICE When replacing the fuse, do not lose any of the small pieces and make sure they are put back in the proper position. The vehicle power cable does not work unless it is assembled correctly. If your device does not charge in your vehicle, you may need to replace the fuse located at the tip of the vehicle adapter. 1 Rotate the end piece 90 degrees counter clockwise to À unlock it. • Take your device out of parking garages and away from tall buildings and trees. • Remain stationary for several minutes. The device does not charge in my vehicle • Check the fuse in the vehicle power cable (Changing the Fuse in the Vehicle Power Cable, page 13). • Verify the vehicle is turned on and is supplying power to the power outlet. • Verify the interior temperature of the vehicle is within the charging temperature range indicated in the specifications. • Verify the fuse is not broken in the vehicle power outlet. My battery does not stay charged for very long • Decrease the screen brightness (Display Settings, page 11). • Shorten the display timeout (Display Settings, page 11). • Decrease the volume (Adjusting the Volume, page 2). • Put the device in power saving mode when not in use (Turning the Device On or Off, page 2). • Keep your device away from extreme temperatures. • Do not leave your device in direct sunlight. My device does not appear as a removable drive on my computer On most Windows computers, the device connects using Media Transfer Protocol (MTP). In MTP mode, the device appears as a portable device and not as a removable drive. MTP mode is supported by Windows 7, Windows Vista®, and Windows XP Service Pack 3 with Windows Media Player 10. My device does not appear as a portable device on my computer On Mac computers and some Windows computers, the device connects using USB mass storage mode. In USB mass storage mode, the device appears as a removable drive or volume, and not as a portable device. Windows versions prior to Windows XP Service Pack 3 use USB mass storage mode. TIP: You may need to use a coin to remove the end piece. 2 Remove the end piece, the silver tip , and the fuse . Á Â 3 Insert a new fast-blow fuse that has the same current, such as 1 A or 2 A. 4 Place the silver tip in the end piece. 5 Push in the end piece and rotate it 90 degrees clockwise to lock it back into the vehicle power cable . Ã Troubleshooting The suction cup will not stay on my windshield 1 Clean the suction cup and windshield with rubbing alcohol. 2 Dry with a clean, dry cloth. 3 Mount the suction cup (Connecting the Device to Vehicle Power, page 2). My device is not acquiring satellite signals • Verify the GPS simulator is turned off (Navigation Settings, page 11). My device does not appear as either a portable device or a removable drive or volume on my computer 1 Disconnect the USB cable from your computer. 2 Turn off the device. 3 Connect the USB cable to your device and to a USB port on your computer. TIP: The USB cable must connect to a USB port on your computer, not to a USB hub. The device turns on automatically and goes into MTP mode or USB mass storage mode. A picture of the device connected to a computer appears on the device screen. NOTE: If you have several network drives mapped on your computer, Windows may have trouble assigning drive letters to your Garmin drives. For information about assigning drive letters, see the help file for your operating system. Appendix Installing a Memory Card for Maps and Data You can install a memory card to increase the storage space for maps and other data on your device. You can purchase memory cards from an electronics supplier, or go to www.garmin.com /maps to purchase a memory card with pre-loaded Garmin Troubleshooting 13