GE AJCQ08AC Owners Manual - Page 9

Notice

Get GE AJCQ08AC PDF manuals and user guides View all GE AJCQ08AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

GEAppliances.com Terminal Connections Remote Thermostat - Class 2 (on some models) The controls are located under a plastic cover behind the front grille. E_] Removethe front grille. Seethe Front Grille _u section of Coreand Cleaning. r_ Removethe screws securing the plastic cover over the wiring connections. Set aside screws and plastic cover. I-j] To make wiring connections, insert the wires into the bottom of the terminals and tighten screws securelg. [] After all desired connections have been made, replace the plastic cover and front grille. The owner is responsible for making all connections and setting the appropriate dip switches. When connected, the unit will be controlled by a remote thermostat. NOTE:Thenumber 3 dip switch must be in the enabled (UPJposition to activate the remote thermostat. (Seethe installation instructions supplied with the remote thermostat.) IMPORTANT: The thermostat connections provide 24 V AConly. If using a digital/electronic wall thermostat, ensure it is compatible with 2/4VACsignal. See the Installation Instructions for the wall thermostat. NOTICE: Damage to a wall thermostat or to the electronics can result from improper connections. Specialcare must be used in connecting the wires. No line voltage connections should be made to any circuit. Isolateall wires in building from line voltage. / Red- 24 V AC only • Green- Low SpeedFan Green- High SpeedFan Yellow- Compressor White - Heater Common- Ground Terminal onnectlons location nderfront grille 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
GEAppliances.com
Terminal
Connections
Remote
Thermostat
- Class 2
(on
some
models)
The controls are located under a plastic cover
behind the front grille.
E_] Removethe front grille. Seethe
FrontGrille
section of
Coreand Cleaning.
r_
Removethe screws securing the plastic cover
over the wiring connections. Set aside screws
and plastic cover.
I-j]
To make wiring connections, insert the wires
into the bottom of the terminals and tighten
screws securelg.
[]
After all desired connections have been made,
replace the plastic cover and front grille.
The owner is responsible for making all
connections and setting the appropriate dip
switches.
When connected, the unit will be controlled
by a remote thermostat.
NOTE:The
number 3 dip switch must be in
the enabled
(UPJ
position to activate the remote
thermostat. (Seethe installation instructions
supplied with the remote thermostat.)
_u
Terminal
onnectlons
location
nderfront
grille
.......................
............
]
IMPORTANT:
The thermostat connections provide 24 V AConly.
If using a digital/electronic wall thermostat,
ensure it is compatible with 2/4VACsignal. See
the Installation Instructions for the wall thermostat.
NOTICE:
Damage to a wall thermostat or to the electronics
can result from improper connections. Specialcare
must be used in connecting the wires. No line
voltage connections should be made to any circuit.
Isolateall wires in building from line voltage.
/
Red- 24 V AC only •
Green- LowSpeedFan
Green- HighSpeedFan
Yellow- Compressor
White - Heater
Common-Ground
9