GE AJCQ10DCG Use and Care Manual - Page 5

Cool Mode, FAN MODE

Get GE AJCQ10DCG PDF manuals and user guides View all GE AJCQ10DCG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Cool Mode Remote Control 1. Press Cool pad. 2. Press Low, Med or High pads to set desired fan speed. 3. Press the Increase +/ Decrease -pads to set the desired temperature 60°F to 85°F in 1°F increments. Control Panel 1. Press the Mode pad until the Cool indicator light is lit and the Low, Med or High indicator light is lit for the desired fan speed. 2. Press the Increase + / Decrease - pads to set the desired temperature 60°F to 85°F in 1°F increments. A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer. NOTE: If the air conditioner is off and is then turned on while set to Cool, it will take approximately 3 minutes for the compressor to start and cooling to begin. Cooling Descriptions )RU1RUPDO&RROLQJ³Select the Cool mode and High or Med fan with a middle set temperature. )RU0D[LPXP&RROLQJ³Select the Cool mode and HIGH fan with a lower set temperature. )RU4XLHWHUDQG1LJKWWLPH&RROLQJ³Select the Cool mode and Low fan with a middle set temperature. NOTE: If you switch from a Cool setting to Off or to a fan setting, wait at least 3 minutes before switching back to a Cool setting. FAN MODE Use the Fan mode to provide air circulation and filtering without cooling. Since fan-only settings do not provide cooling, a temperature setting will not be displayed. Remote Control Press Fan pad. Press Low, Med or High pads to set desired fan speed. Control Panel Press the Mode pad until the Fan indicator light is lit and the Low, Med or High indicator light is lit for the desired fan speed. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
5
Cool Mode
Remote Control
1.
Press
Cool
pad.
2.
Press
Low, Med
or
High
pads to set desired fan speed.
3.
Press the
Increase +/ Decrease –
pads to set the desired
temperature 60°F to 85°F in 1°F increments.
Control Panel
1.
Press the
Mode
pad until the
Cool
indicator light is lit and the
Low,
Med
or
High
indicator light is lit for the desired fan speed.
2.
Press the
Increase + / Decrease –
pads to set the desired
temperature 60°F to 85°F in 1°F increments.
A thermostat is used to maintain the room temperature. The
compressor will cycle on and off to keep the room at the set level of
comfort. Set the thermostat at a lower number and the indoor air will
become cooler.
Set the thermostat at a higher number and the indoor air will become
warmer.
NOTE:
If the air conditioner is off and is then turned on while set to
Cool
, it will take approximately 3 minutes for the compressor to start
and cooling to begin.
Cooling Descriptions
Select the
Cool
mode and
High
or
Med
fan with
a middle set temperature.
Select the
Cool
mode and
HIGH
fan with a
lower set temperature.
Select the
Cool
mode and
Low
fan with a middle set temperature.
NOTE: If you switch from a Cool setting to Off or to a fan setting,
wait at least 3 minutes before switching back to a Cool setting.
FAN MODE
Use the
Fan
mode to provide air circulation and filtering without
cooling. Since fan-only settings do not provide cooling, a temperature
setting will not be displayed.
Remote Control
Press
Fan
pad. Press
Low, Med
or
High
pads to set desired fan speed.
Control Panel
Press the
Mode
pad until the
Fan
indicator light is lit and the
Low, Med
or
High
indicator light is lit for the desired fan speed.