GE ASM14AL Owners Manual - Page 13

& Caution

Page 13 highlights

Window Installation Instructions [] INSTALL THE CASE IN THE WINDOW [] Cut the window sash seal to the window width and stick the adhesive side to the bottom of the sash. Window sill Window sash seal [] Thread two type C bolts into the support brackets, Slide the case into the window and lower the window behind the top mounting rail. Position the brackets on the case bottom so they will be near the outermost point on the window sill. Attach the support brackets to each side of the case bottom using 4 type A screws on each side. The case should be slightly tilted to the outside, Use a level; about a 1/2 bubble will be the correct case slant to the outside, Adjust the leveling bolts to touch the sill, U [] INSTALL THE CASE IN THE WINDOW (cont.) [] Locate the 8 screw holes along the bottom front edge of the case, Center the case, sideto-side, in the window and mount it to the window sill using 5 type B screws staggered in the front and back rows if possible, Top mounting rail Type B screws Type B screws Type B screws [] Extend the left and right accordion panels to the vertical window sashes and attach with 4 type B screws. [] INSTALL THE SECURITY BRACKET AND THE FOAM TOP WINDOW GASKET [] Attach the security bracket with a type B screw. Window sill -----__ _iype ,Type A screws C bolts -& CAUTION: Ifthesillsupport bolts do not contact the window sill, or if you have a window without a sill, you must order accessory kit RAK87 to properly install this air conditioner. Call 800.626.2002 or visit ge.com. [] Cut the foam top window gasket to the window width. [] Stuff the foam between the glass and the window to prevent air and insects from getting into the room. / 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

Window
Installation
Instructions
[]
INSTALL THE CASE
IN THE WINDOW
[]
Cut the
window
sash
seal
to
the window
width
and stick
the adhesive
side
to the
bottom
of the sash.
Window
sill
Window
sash seal
[]
Thread
two
type
C bolts
into the support
brackets,
Slide
the case
into the window
and
lower
the window
behind
the top
mounting
rail.
Position
the brackets
on the case bottom
so
they
will
be near
the outermost
point
on the
window
sill. Attach
the support
brackets
to
each side
of the case bottom
using
4 type
A
screws
on each side.
The
case should
be
slightly
tilted
to the outside,
Use a level;
about
a 1/2 bubble
will
be the correct
case
slant
to the outside,
Adjust
the leveling
bolts
to touch
the sill,
Window
sill -----__
U
,Type
A screws
_iype
C bolts
-& CAUTION:
If
thesill
support
bolts
do not contact
the
window
sill,
or if you
have
a window
without
a sill,
you
must
order
accessory
kit RAK87
to
properly
install
this
air conditioner.
Call
800.626.2002
or visit
ge.com.
[]
INSTALL THE
CASE
IN THE
WINDOW
(cont.)
[]
Locate
the 8 screw
holes
along
the bottom
front
edge
of the
case, Center
the case, side-
to-side,
in the window
and
mount
it to the
window
sill
using
5 type
B screws
staggered
in the front
and
back rows
if possible,
Top mounting
rail
Type B
screws
Type B screws
Type B
screws
[]
Extend
the left and
right
accordion
panels
to
the vertical
window
sashes
and attach
with
4 type
B screws.
[]
INSTALL
THE SECURITY
BRACKET
AND
THE FOAM
TOP
WINDOW
GASKET
[]
Attach
the
security
bracket
with
a type
B
screw.
[]
Cut the foam
top
window
gasket
to the
window
width.
[]
Stuff
the foam
between
the glass
and the
window
to
prevent
air and
insects
from
getting
into the
room.
/
13