GE DPVH880GJMV Owners Manual - Page 42

WARNING, Installation Instructions, STACKING THE WASHER AND DRYER if desired cont.

Get GE DPVH880GJMV - ProfileTM 7.5 cu. Ft. Gas Dryer PDF manuals and user guides
UPC - 084691169796
View all GE DPVH880GJMV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Installation Instructions STACKING THE WASHER AND DRYER (if desired) (cont.) 3 INSTALL BRACKET TO DRYER A. Align the holes in the left bracket with the holes in the bottom left corner of the dryer. Use a Phillips screwdriver to install the 2 #12 x 1″ tapping screws. B. Repeat the above step with the right bracket on the bottom right corner of the dryer. C. Set the dryer upright. NOTE: Make sure to set the dryer on a piece of packing material so the brackets that are attached to the bottom of the dryer do not damage the floor. 5 FINALIZE THE INSTALLATION A. Refer to the washer Installation Instructions to complete the washer installation. B. Refer to the dryer Installation Instructions to complete the dryer installation. C. Carefully slide or walk the stacked washer and dryer into place. Use felt pads or other sliding device to assist moving and to protect flooring. WARNING - Potential Personal Injury. Do not push on the dryer once installed to top of the washer. Pushing on the dryer may result in pinched fingers. 4 INSTALL DRYER AND BRACKET ON WASHER Place hands here Place hands here A. Lift the dryer on top of the washer. Be careful not to scratch the top of the washer with the brackets. Protect the washer control panel with cardboard or other protection. Be sure to lift the dryer high enough to clear the washer control panel. WARNING - Potential Personal Injury. More than two people are recommended to lift the dryer into position because of its weight and size. Failure to do so could result in personal injury or death. B. Align the holes in the bracket with the holes in the back of the washer. Using a Phillips screwdriver, attach the 2 #8 x 1/2″ tapping screws. Repeat on both sides of the washer. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
INSTALL BRACKET TO DRYER
A.
Align the holes in the left bracket with the holes
in the bottom left corner of the dryer. Use a
Phillips screwdriver to install the 2 #12 x 1
″
tapping screws.
B.
Repeat the above step with the right bracket
on the bottom right corner of the dryer.
C.
Set the dryer upright.
NOTE:
Make sure to set the dryer on a piece of
packing material so the brackets that are attached
to the bottom of the dryer do not damage the floor.
3
INSTALL DRYER AND BRACKET
ON WASHER
A.
Lift the dryer on top of the washer. Be careful
not to scratch the top of the washer with the
brackets. Protect the washer control panel with
cardboard or other protection. Be sure to lift
the dryer high enough to clear the washer
control panel.
WARNING –
Potential
Personal Injury. More than two people are
recommended to lift the dryer into position
because of its weight and size. Failure to do
so could result in personal injury or death.
B.
Align the holes in the bracket with the holes
in the back of the washer. Using a Phillips
screwdriver, attach the 2 #8 x 1/2
″
tapping
screws. Repeat on both sides of the washer
.
4
FINALIZE THE INSTALLATION
A.
Refer to the washer Installation Instructions
to complete the washer installation.
B.
Refer to the dryer Installation Instructions
to complete the dryer installation.
C.
Carefully slide or walk the stacked washer and
dryer into place. Use felt pads or other sliding
device to assist moving and to protect flooring.
WARNING –
Potential Personal
Injury. Do not push on the dryer once installed
to top of the washer. Pushing on the dryer may
result in pinched fingers.
5
Place
hands
here
Place
hands
here
Installation Instructions
42
STACKING THE WASHER AND DRYER (if desired) (cont.)