GE GBC12IAXLSS Use and Care Manual - Page 7

Caution

Get GE GBC12IAXLSS PDF manuals and user guides
UPC - 084691176459
View all GE GBC12IAXLSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Safety Instructions Operating Instructions GEAppliances.com Preparing for Long Vacations For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open. If the temperature can drop below freezing, have a qualified servicer drain the water supply system (on some models) to prevent serious property damage due to flooding. Preparing to Move Secure all loose items such as base grille, shelves and drawers by taping them securely in place to prevent damage. When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator. Be sure the refrigerator stays in an upright position during moving. Replacing the Light Bulbs Turning the control to the Cold position does not remove power to the light circuit. CAUTION: Light bulbs may be hot. Unplug the refrigerator. The bulbs are located at the top of the refrigerator compartment behind the controls. To remove the light shield, grasp the shield at the back and pull out to release the tabs at the back. Rotate the shield down and then forward to release the tabs at the front of the shield. After replacing with an appliance bulb of the same or lower wattage, replace the shield. Plug the refrigerator back in. NOTE: If a bulb is not available at your local store, please contact GE Customer Support. Installation Instructions Troubleshooting Tips Consumer Support 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
7
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
GEAppliances.com
For long vacations or absences, remove
food and unplug the refrigerator. Clean the
interior with a baking soda solution of one
tablespoon (15 ml) of baking soda to one
quart (1 liter) of water. Leave the doors open.
If the temperature can drop below freezing,
have a qualified servicer drain the water
supply system (on some models) to prevent
serious property damage due to flooding.
Preparing for Long Vacations
Preparing to Move
Secure all loose items such as base grille,
shelves and drawers by taping them
securely in place to prevent damage.
When using a hand truck to move the
refrigerator, do not rest the front or back
of the refrigerator against the hand truck.
This could damage the refrigerator. Handle
only from the sides of the refrigerator.
Be sure the refrigerator stays in an upright
position during moving.
Turning the control to the
Cold
position does not remove power to the light circuit.
CAUTION:
Light bulbs may
be hot.
Unplug the refrigerator.
The bulbs are located at the top of the
refrigerator compartment behind the
controls. To remove the light shield, grasp
the shield at the back and pull out to
release the tabs at the back.
Rotate the shield down and then
forward to release the tabs at the front
of the shield.
After replacing with an appliance bulb
of the same or lower wattage, replace
the shield.
Plug the refrigerator back in.
NOTE:
If a bulb is not available at your local
store, please contact GE Customer Support.
Replacing the Light Bulbs