GE NX-8 Installation Manual - Page 22

L LOCATION 40 - SYSTEM TIMERS (10 segments, numerical data) Location 40 contains the duration of various system timing functions. Example: If you desire the duration of the Dynamic Battery Test to be 30 minutes, you should program [3]-[0]-[r] in segment 1 of this location. The [3]-[0] is the number of minutes, and the [r] stores the data and moves to the next segment of this location. Segment 1 - Dynamic Battery Test duration in minutes 0-255 minutes ("0" = no test) Segment 2 - AC Fail report delay in minutes 0-255 minutes. Segment 3 - Power Up Delay in seconds 0-60 seconds ("0" = no power up delay). Segment 4 - Siren Time in minutes 1-255 minutes. Segment 5 - Telephone Line Cut delay in seconds 0-255 seconds ("0" = no TLM). Segment 6 - Cross Zone time in minutes 0-255 ("0" = no cross zoning). Segment 7 - Chime time in 50 mS (1/20th second) increments from 0-12 seconds ("0" = follows zone 255 latched). Segment 8 - Dial delay in seconds 0-255 seconds ("0 " = no abort delay). Segment 9 - Fire Alarm Verification time in seconds 120-255 seconds ("0" = no fire alarm verification). NOTE: This feature is not approved for residential use in California Segment 10 -Listen-In time in seconds 0-255 ("0" = no Listen-In time). Note: The "Listen-In" feature cannot be enabled for UL Listed systems. The "Dynamic Battery Test" feature cannot exceed four (4) hours. The dial delay shall be set to -0-. LOCATION 41 - SPECIAL FEATURES (1 segment, feature selection data) Segment 1: 1 - On enables the 6-digit code option. If 6-digit option is enabled, all arm/disarm codes and the "Go To Program Code" are 6 digits. If this option is enabled, the default user 1 code is [1]-[2]-[3]-[4]-[5]-[6]. NOTE: IF YOU ENABLE THIS OPTION, VERIFY THAT THE "GO TO PROGRAM CODE" IS A SIXDIGIT CODE BEFORE EXITING PROGRAMMING. 2 - On requires code entry for [r]-[9]-[8] (perform call back download) and [r]-[9]-[9] (answer incoming call for download) functions. 3 - Enable Auto Cancel / Abort (Refer to feature definitions beginning on page 3) 4 - Enable Walk-Test Mode (Refer to feature definitions beginning on page 3) 5-8 Reserved. L LOCATION 42 - GO TO PROGRAM CODE (6 segments, numerical data) Location 42 contains the "Go To Program Code". This location contains either a 4 or 6-digit code. If the 6-digit code option is enabled in Location 41, THIS CODE MUST CONTAIN SIX (6) DIGITS. If this option is not enabled in location 41, the last 2 segments (digits) will be ignored. With the NX-8 disarmed, the "Go To Program Code" can be used to enter the Program Mode. LOCATION 43 - GO TO PROGRAM CODE PARTITION AND AUTHORIZATION (2 segments, feature selection) The "Go To Program Code" can be used as a standard arm/disarm code. When using the code to arm or disarm, the user ID is 255. (This code may not be changed in the Run Mode.) Segment 1: Segment 2: 1 - Reserved. 2 - On enables "Go To Program Code" as an arm only code. 3 - On enables "Go To Program Code" as an arm only after closing. 4 - On enables "Go To Program Code" as a master arm/disarm code (can change user codes) 5 - On enables "Go To Program Code" as an arm/disarm code. 6 - On enables "Go To Program Code" to bypass zones. 7 - On enables "Go To Program Code" opening and closing reports. 8 - Reserved. 1 - On enables the "Go To Program Code" for Partition #1. 2 - On enables the "Go To Program Code" for Partition #2. 3 - On enables the "Go To Program Code" for Partition #3. 4 - On enables the "Go To Program Code" for Partition #4. 5 - On enables the "Go To Program Code" for Partition #5. 6 - On enables the "Go To Program Code" for Partition #6. 7 - On enables the "Go To Program Code" for Partition #7. 8 - On enables the "Go To Program Code" for Partition #8. L LOCATION 44 - DURESS CODE (6 segments, numerical data) Page 22